User Account

All Pages

The water leaves the tube leaves at the 1mpa and 300oc with

Assignment Help Mechanical Engineering
Reference no: EM13611409

Water at 1MPa and 65oC enters a tube of a boiler which has a constant 160mm inside-diameter. The water leaves the tube leaves at the 1MPa and 300oC with a velocity of 80m/s. Calculate the 1) volume flow rate at the outlet; 2) mass flow rate at the inlet; and 3) velocity at the inlet.

Reference no: EM13611409

Questions Cloud

Luthan company uses a predetermined overhead rate of 2340 : luthan company uses a predetermined overhead rate of 23.40 perdirect labor-hour. this predetermined rate was based on
The only information you have about a proposed site for a : the only information you have about a proposed site for a wind farm is that the wind blows at speeds above 25 ms 90 hrs
The following present value factors are provided for use in : the following present value factors are provided for use in this problem present value present value of an periods of 1
A value that causes the 24 hr average velocity to be 20 ms : a wind turbine with a swept area of 1000 m2 operates with 56 efficiency under stp conditions. at the location of the
The water leaves the tube leaves at the 1mpa and 300oc with : water at 1mpa and 65oc enters a tube of a boiler which has a constant 160mm inside-diameter. the water leaves the tube
Calculate the cash dividends required to be paid for each : calculate the cash dividends required to be paid for each of the following preferred stock issuesrequireda the
A student takes a calculus midterm and a history midterm : a student takes a calculus midterm and a history midterm. the mean and standard deviation on the calculus midterm are
When an object falls and hits the floor without bouncing : when an object falls and hits the floor without bouncing off the floor the normal force of the floor on the object
Calculate the brake kw of the fan if its efficiency is 65 : a centrifugal fan is to be used to take a flue gas at rest zero velocity and at a temperature of 352.6 k and a pressure

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Prepare a journal paper on renewable energy

Prepare a Journal paper on Renewable Energy

  The diffusion constant do and activation energy q of c in

the diffusion constant do and activation energy q of c in bcc fe is 0.01 cm2sec and 80kjmol respectively. in fcc fe the

  Determine the maximum contact pressure

The wheel of a crane lift is rolling on a flat rail. The radius of the wheel is 4 in, the contact length and force are 2.5 in and 1 ton respectively, and E = 30 MPa and ν = 0.3 for both parts. Determine (a) the maximum contact pressure, (b) the wi..

  Does this engine satisfy the increase of entropy principle

a heat engine whose thermal efficiency is 40 percent uses a hot reservoir at 700 k and a cold reservoir at 280 k. a

  Five kilograms of water at saturated liquid phase fills in

five kilograms of water at saturated liquid phase fills in a piston-cylinder device at 150oc. the device is now heated

  Also calculate specific steam consumption bwr quality of

determine cycle efficiency of steam power plant . boiler pressure 80bar condenser 0.1bar turbine inlet temperature

  What is the relationship between la and lb

Two simple pendulums are related as follows. Pendulum A has a length LA and a bob of mass mA; pendulum B has a length LB and a bob of mass If the period of A is twice that of B, What is the relationship between LA and LB?

  Determine the temperature of the air at the compressor exit

an air compressor operates at steady state with air entering at p11 bar t1 17 c and exiting at p25 bar. the air

  Determine the force exerted on the hoist by the htdraulic

A small hoist is mounted on the back of a pickup truck and is used to lift a 500N crate . Determine the force exerted on the hoist by the htdraulic cylinder BC, the reaction at A.

  Explain why the two measurements give different values

A similar measurement is made applying the force parallel to one of the cube axes. Explain why the two measurements give different values of the elastic modulus.

  A gas in an insulated tank is separated from an evacuated

a gas in an insulated tank is separated from an evacuated region by a membrane. the membrane is removed and the gas is

  Complete the sketch of the obtuse triangle

Complete the sketch of the obtuse triangle. It must have an area of 1.75 in.2. Prove the geometry by dimensioning the sketch and showing the area calculation. Show only those dimensions needed for the area calculation. Note: each grid unit = .25 i..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd