The volume flow rate at the exit of the pipe

Assignment Help Mechanical Engineering
Reference no: EM13701022

Carbon-dioxide gas at 3MPa and 500 K flows steadily in a pipe at a rate of 0.4kmol/s. Determine a) the volume and mass flow rates and the density of carbon dioxide at this state. If CO2 is cooled at a constant pressure as it flows in the pipe so that the temperature of CO2 drops to 450 K at the exit of the pipe, determine b) the volume flow rate at the exit of the pipe.

Reference no: EM13701022

Questions Cloud

Using constant specific heats at room temperature : A closed gas turbine unit uses neon as the working fluid. There are two stages of compression with inter cooling from 480kPa and 290K to a maximum pressure of 2.75MPa with an intermediate pressure of 1149kPa. The regenerator has an effectiveness of 6..
For an adiabatic in viscid flow : For an adiabatic in viscid flow, write the entropy equation in general coordinate-independent form and in Cartesian coordinates. What does the equation express? Can we say that entropy is constant in an entire such flow (explain your answer)?
What range of input voltages would produce : An 8-bit ADC with a 10.0-V reference has an input of 3.797 V. Find the digital out- put word. What range of input voltages would produce this same output? Suppose the output of the ADC is 101101112. What is the input voltage?
Find the output voltage produced : A 6-bit DAC has an input of 1001012 and uses a 10.0-V reference. a. Find the output voltage produced. b. Specify the conversion resolution.
The volume flow rate at the exit of the pipe : Carbon-dioxide gas at 3MPa and 500 K flows steadily in a pipe at a rate of 0.4kmol/s. Determine a) the volume and mass flow rates and the density of carbon dioxide at this state. If CO2 is cooled at a constant pressure as it flows in the pipe so that..
A rich benefactor calls a meeting with two deans : A rich benefactor calls a meeting with two Deans. The benefactor wishes to make a $100 donation to the two schools, but requires the deans to engage in the following bargaining game to divide the money. First the Dean L offers the Dean R a porti..
What maximum shear stress is experienced by other surface : A cylinder is internally pressurized to a pressure of 100 MPa. This cause tangential and axial stress in the outer surface of 400 and 200 MPa respectively. Make a mohr circle representing of the stress in the outer surface. What maximum shear stress ..
Significant event relate to the changes on health care : How does this significant event relate to the changes on health care and in your opinion, has this event impacted the historical evolution of health care? If so, how? If not, could it?
Determine the amount of heat transferred to the system : A piston contains 0.5kg of water. The initial volume of the piston is 0.125 m3 and the pressure inside the piston is 300kPa. The water is expanded to a volume of .31701 m3. The pressure inside the piston remains constant. Determine the amount of heat..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd