The valve opens and steam enters the tank the valve closes

Assignment Help Mechanical Engineering
Reference no: EM13636891

A 0.1 m^3 rigid cylinder contains saturated water vapor at 100kPa. A pipe with super heated steam at 1MPa, 300 degree C is connected to the tank through a valve. The valve opens and steam enters the tank. The valve closes when the water is a 500Kpa and saturated liquid conditions.

a) draw a schematic of the system
b) determine Boundary work
c) heat transfer (kJ)
d) entropy generated
use a boundary temperature of 50 degree C

Reference no: EM13636891

Questions Cloud

A shell oil company executive says that a majority of : a shell oil company executive says that a majority of workers more than 50 prefer a 10 hour four day work week over an
Suppose that the charge were all pushed away from the : a charge of -5.00 nc is spread uniformly over the surface of one face of a nonconducting disk of radius 1.00cm .a find
Suppose the historical average work week was 392 hours and : suppose the historical average work week was 39.2 hours and sd was 4.8 hours as reported by the department of labor.
Which two packaging plastics should show ir absorptions due : which two packaging plastics should show ir absorptions due toa benzene ring and which one is the addition polymerand
The valve opens and steam enters the tank the valve closes : a 0.1 m3 rigid cylinder contains saturated water vapor at 100kpa. a pipe with super heated steam at 1mpa 300 degree c
Suppose a 95 confidence interval is computed for u : 1. suppose a 95 confidence interval is computed for u resulting in the interval 112.4 121.6. then it would be accurate
At a place on earth whcre thc local acceleration of gravity : an instrumcnt to measure the acceler.ttion of gravity on mars is constructed of a spring from which is suspendcd a mass
A 3 cubic meter tank contains 15 kg of a gas at 27oc and : a 3 cubic meter tank contains 1.5 kg of a gas at 27oc and avacuum pressure of 81 kpa. what is the density and
Find the sample standard deviation find the 99 confidence : the grade point averages gpa for 12 randomly selected college students are shown below. assume the population is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd