The total number of cells in device is 2109 the rate of

Assignment Help Mechanical Engineering
Reference no: EM13619622

You are designing an ex vivo artificial organ. The cells in the organ cannot tolerate shear stress in excess of 0.5 g/cm s^2. You need to design channels to deliver the nutrients to the cells. The total number of cells in device is 2*10^9. The rate of oxygen metabolism is 7.8 nmol oxygen/min/mg of cells. The cell mass is 33.7*10^ -12g/cell.

1-How much oxygen must be delivered to the device per second?

2-Assume that the dissolved oxygen concentration in media ( that is flowing over the cells) is 0.2 mmol/litter of media. What volume of fluid must be pumped into device per second?

3-Assuming the cells are 20 micrometer diameter discs, how much surface area is required for the plate if they are cultured as a monolayer (single layer-not one on top of another)?

4-Plot shear stress and oxygen flux as a function of position?

You can assume the properties of media to be that of water and whole system to be at 37 C, cleary state all assumptions made.

Reference no: EM13619622

Questions Cloud

What is the heat loss per unit length of pipe when heated : a pipeline used for the transport of crude oil is buried in the earth such that its centerline is a distance of 1.5m
Suppose the conditional distribution of y given x x is : suppose the conditional distribution of y given x x is gamma with ? 4 and ? 1x and the marginal distribution of x is
Given three resistors r1 2 ohms r23 ohms and r3 4 ohms how : given three resistors r1 2 ohms r23 ohms and r3 4 ohms. how many combinations of equivalent resistance can you have.
A study is to be conducted on the proportion of us citizens : a study is to be conducted on the proportion of u.s. citizens who believe the minimum wage should be raised. what is
The total number of cells in device is 2109 the rate of : you are designing an ex vivo artificial organ. the cells in the organ cannot tolerate shear stress in excess of 0.5 gcm
What is the expected number of times that you play prior to : an urn contains nine white balls and 11 black balls. a ball is drawn and replaced. if the ball is white your opponent
One such device generates an upward magnetic field within : transcranial magnetic stimulation is a noninvasive technique used to stimulate regions of the human brain. a small coil
You purchase a new motor vehicle and are considering : you purchase a new motor vehicle and are considering purchasing an extended bumper-to-bumber warranty. the extended
Two solenoidal coils a and b are wound using equal lengths : two solenoidal coils a and b are wound using equal lengths of the same kind of wire. the length of the axis of each

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd