User Account

All Pages

The temperature at the end of the isentropic expansion

Assignment Help Mechanical Engineering
Reference no: EM13618973

The compression ratio of an air-standard ideal Otto cycle is 10. Prior to the isentropic compression process, the air is at 100 kPa, 35 ºC, and 600 cm3. The temperature at the end of the isentropic expansion process is 800 K. Using specific heat values at room temperature, determine:

(a) the highest temperature and pressure in the cycle.

(b) the amount of heat transferred in, in kJ.

c) the thermal efficiency.

(d) draw the P- v diagram for this process.

Reference no: EM13618973

Questions Cloud

You are planning to save for retirement over the next 30 : you are planning to save for retirement over the next 30 years. to do this you will invest 890 a month in a stock
Given the following changes in current assets and current : given the following changes in current assets and current liabilities what is the change in nwc? the change in accounts
Air is compressed in a piston-cylinder device from 90 kpa : air is compressed in a piston-cylinder device from 90 kpa and 20 degrees c to 400 kpa in a reversible isothermal
Smaltzs capital structure is comprised of 75 equity based : smaltz enterprises is currently involved in its annual review of the firms cost of capital. historically the firm has
The temperature at the end of the isentropic expansion : the compression ratio of an air-standard ideal otto cycle is 10. prior to the isentropic compression process the air is
The power of this test against the alternative hypothesis : an experimenter suspects that a certain die is loaded that is the chances that the die lands on different faces are not
You are planning to make monthly deposits of 440 into a : you are planning to make monthly deposits of 440 into a retirement account that pays 9 percent interest compounded
The mass flow rate of the refrigerant is 005 kgs show the : a refrigerator uses refrigerant-134a as the working fluid and operates on an ideal vapor-compression refrigeration
Tarzan swings on a 300 m long vine initially inclined at an : tarzan swings on a 30.0 m long vine initially inclined at an angle of 37.0o with the vertical.a sketch a diagram and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Deterimine reaction exerted by the groung on the airs

the 1-Mg forklift is used to raise the 750-kg crate with acceleration of 2 m/s. deterimine reaction exerted by the groung on the airs of wheel at A and B.

  Calculate the largest semicircular surface flaw oriented

calculate the largest semicircular surface flaw oriented along the axis of the bores that could withstand a fluid pressure of 50MPa.

  Computing the second moment of area

It is necessary to design a square-section composite bar that will withstand an applied load without deflecting more than a specified amount.The design specification for the bar, including its dimensions and loading criteria, is given below.

  If the barometric pressure was 100 kpa and the humidity was

temperature in state college pa on 31st december 2012 was 22 f. if the barometric pressure was 100 kpa and the humidity

  Assuming that the condensate flow is laminar calculate the

in a laboratory steam is condensed at atmospheric pressure i.e. 212degf on the shell-side of a vertically-oriented

  You are to supply a design for an engine room crane

You are to supply a design for an engine room crane which will provide maintenance support for the main engine. Your design should include the rails the crane will sit on.

  Generate a script to draw the perpendicular bisector of

generate a script to draw the perpendicular bisector of any two points using ginput command. the length of the

  Find the angular velocity of link cd

(a) Find the angular velocity of link CD and the velocity of the pin relative to the slot in link CD. (b) Find the angular acceleration of link CD and the acceleration of the pin relative to the slot in link CD.

  Observing plastic deformationthe aim of this demonstration

observing plastic deformationthe aim of this demonstration is to make some observations of the surface relief produced

  Water flows through a pipe ab 12 m diameter at 3 ms and

water flows through a pipe ab 1.2 m diameter at 3 ms and then passes through a pipe bc 1.5 mdiameter. at c the pipe

  The heat rejection temperature is 70 f for the same

a fossil-fuel steam power plant operates at about 50 of carnot thermal efficiency. it has been suggested that the air

  The radius of the curvilinear path is 4 in what is the

the position of a particle moving in a curvilinear path is given by thetacos2t where theta units are radians and t

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd