The telescope mirror design was approved and a container

Assignment Help Mechanical Engineering
Reference no: EM13623309

A team of astronomers have proposed to construct a large parabolic telescope mirror by spinning a cylindrical container of mercury (rho = 13,500 kgm-3). The dish would be 10 m in diameter and spin at an angular velocity of 0.5 rad s-1. What is the minimum volume of mercury to prevent the base of the container from being exposed during operation? Assume that the container has a flat bottom and vertical sidewalls, and the liquid is in solid-body rotation. Volume = 12.5 m3, fluid height = 0.319 m at the side walls The telescope mirror design was approved, and a container must be sized to support the load of the spinning mercury. What is the tension force in the container side-walls.

Reference no: EM13623309

Questions Cloud

As a 32000 lb airplane takes off the tangential component : as a 32000 lb airplane takes off the tangential component of the force exerted by its engines is ft45000lb. neglecting
You are scheduled to receive annual payments of 5100 for : you are scheduled to receive annual payments of 5100 for each of the next 7 years. the discount rate is 10 percent.
Determine the acceleration of the water particles that are : a sprinkler essentially consists of a pipe ab mounted on a hollow shaft. the water comes in the pipe at o and goes out
Assuming that the molecules are moving at their : the mean free path of an oxygen molecule is 2.0 times 10-5 m when the gas is at a pressure of 120 pa and a temperature
The telescope mirror design was approved and a container : a team of astronomers have proposed to construct a large parabolic telescope mirror by spinning a cylindrical container
The government has imposed a fine on the corner tavern the : the government has imposed a fine on the corner tavern. the fine calls for annual payments of 125000 100000 75000 and
Highway express has paid annual dividends of 105 120 125 : highway express has paid annual dividends of 1.05 1.20 1.25 1.15 and 0.95 over the past five years respectively. what
The near point of the person using the microscope is 245 : to examine a particular blood sample in biology lab a student uses a compound microscope set to have a magnification of
The headlights of on a small car are separated by 115 cm at : the headlights of on a small car are separated by 115 cm. at what maximum distance could you resolve them if the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd