The storage tank of a water tower is a vertical cylinder of

Assignment Help Mechanical Engineering
Reference no: EM13627336

The storage tank of a water tower is a vertical cylinder of diameter D = 7 m, the initial depth of water within it is ho =6 m and the free surface is exposed to the atmosphere. The base of this tank is supported at a height H = 15 m above the ground and a single vertical drainage pipe leading from its base has a diameter d = 140 mm and a length L = 14 m. The inlet to the pipe is sharp-edged and has k in = 0.5, the outlet valve when fully open has k out = 1 and the pipe may be considered to have a constant friction factorf= 0.007. The water is allowed to discharge to the atmosphere at the exit from the drainage pipe.

a). Find the time taken for the liquid level in the tank to fall to hI = 1 m after the valve has been fully opened.

Reference no: EM13627336

Questions Cloud

An experiment can result in one or both of events a and b : an experiment can result in one or both of events a and b with the probabilities events a and b with the probabilities
Required gusset plate and thickness for the tensile : 1. for the connection shown in figure assuming the bolts are frac34- in. diameter and the angle and plate astm a36
Sketch not to scale the variation of shear stress vs shear : sketch the variation of shear stress vs shear strainnot to scale along the radius in a composite bar of total radius r
Find the maximum and minimum transmittance of the : the plates of a fabry-perot interferometer are coated with silver of such a thickness that for each plate the
The storage tank of a water tower is a vertical cylinder of : the storage tank of a water tower is a vertical cylinder of diameter d 7 m the initial depth of water within it is ho
Assuming the piano strong has too low a pitch what percent : a piano tuner hears a beat frequency of 6.2 hz when comparing the pianos a-string against a reference tuning fork
The flywheel of a small punching machine rotates at 360 rpm : the flywheel of a small punching machine rotates at 360 rpm. each punching operation requires 1500 ft-lb of work and it
If the score recorded in the grade book is the total number : an instructor has given a short quiz consisting of two parts. for a randomly selected student let x the number of
How long does an organ pipe have to be if it is closed at : how long does an organ pipe have to be if it is closed at one end open at the other and has a fundamental frequency of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd