User Account

All Pages

The speed of water at the beginning of the pipe is 150 fts

Assignment Help Mechanical Engineering
Reference no: EM13613602

Water flows into an 9.0" diameter section of a piping system then it exits from 3.0" x 4.0" rectangular section. The speed of water at the beginning of the pipe is 15.0 ft/s. What is the speed of the water flowing out of the 3.0" x 4.0" rectangular section in ft/min?

Reference no: EM13613602

Questions Cloud

The steam is at 2 mpa and 400 c at the inlet the steam : steam is expanded in an adiabatic turbine from a single inlet to a single oulet during an internally reversible
The tube has no external heat transfer and no koving parts : a vortex tube has an air inlet flow at 20 degrees celsius 200 kpa and two exit flows of 100 kpa one at 0 degrees
Room b has 15 kg air at 20 degrees celsius both rooms at : a rigid insulated container has two rooms seperated by a membrane. room a contains 1 kg air at 200 degrees celsius and
The lifetime of one of dotcoms electronic equipment has a : comparing continuous distributionsthe lifetime of one of dotcoms electronic equipment has a mean of 400 hours and
The speed of water at the beginning of the pipe is 150 fts : water flows into an 9.0 diameter section of a piping system then it exits from 3.0 x 4.0 rectangular section. the speed
Suppose certain coins have weights that are normally : suppose certain coins have weights that are normally distributed with a mean od 5.492 g and a standard deviation of
Your client is considering two investments and has asked : your client is considering two investments and has asked you to evaluate these alternatives. provide financial and risk
Finally it comes to a stop in one half a rotations what was : a 50 kg winding drum 75 cm in diameter is used to reel in cable. it is moving at the rate of 2 revolutions per second.
Ar at 100 lbf in 2 500 degree f and a velocity of 100 ft : air at 100 lbf in 2 500 degree f and a velocity of 100 ft s enters a nozzle operating at steady state and expands

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the thermal efficiency of the system assuming

air enters the compressor of a regenerative gas-turbine engine at 300 k and 100 kpa where it is compressed to 800 kpa

  Explain force exerted on the body by the fluid motion

In flows past solid bodies, the force exerted on the body by the fluid motion depends upon the fluid velocity u, the density p, the viscosity

  Carrying a uniformy distributed load

The bending moment M at position x m from the end of a simply supported beam of lenght L m carrying a uniformy distributed load of w Kn m-1 is given by

  The pipe are filled with ethyl alcohol to a level of 15 m

a cylindrical tank with its axis horizontal has a diameter of 2.0 m and a length of 4.0 m. the ends if the tank are

  Calculate the adiabatic flame temperature

Calculate the adiabatic flame temperature (at constant pressure) for ethane C2H6 in air

  Determine the corresponding angular velocity of gear b

Gear A rotates with an angular velocity of 100 rpm clockwise. Knowing that the angular velocity of arm AB is 50 rpm counterclockwise, determine the corresponding angular velocity of gear B.

  Estimate the smallest diameter of a rod

The compression strength of Kevlar 49 fiber is about one-eight of its tensile stress. Estimate the smallest diameter of a rod on which 12 um diameter Kevlar fiber can be wound without causing kinks on its compression side.

  Calculate the heat transfer and the work done

Saturated water vapor at 200oC is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the heat transfer and the work done during this process in kJ/kg.

  Determine a the largest value less than 45deg of the angle

the initial velocity v0 of a hockey puck is 105 mih. determine a the largest value less than 45deg of the angle a for

  If the volume of the air in the tank is 2 cubic meters find

an insulated rigid-wall tank contains air at 20 c and 2 bar. a paddle wheel located in the tank does work on the air in

  What thickness of extruded polystyrene sheet must be

a new building to be located in a cold climate is being designed with a basement that has an l 200-mm-thick wall. inner

  The condenser operates at 10 kpa determinea the mass flow

a steam power plant implements an ideal reheat rankine cycle. steam enters the inlet of the high-pressure turbine at 8

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd