The spacing of the bands be near the bottom of the vat

Assignment Help Mechanical Engineering
Reference no: EM13704620

A cylindrical wooden storage vat has a 20 ft outside diameter. It is filled with 24 feet of brine with a specific gravity of 1.06. The wooden staves making up the vat are bound by flat steel bands evenly spaced vertically around the tank. Each band is 2-inches wide and ¼-inch thick. The allowable stress in each band is 16,000 psi. What should the spacing of the bands be near the bottom of the vat? Neglect any initial stress that is applied to the bands. Hint: Think of how we did the derivation for a cylindrical pressure vessel.

Reference no: EM13704620

Questions Cloud

Consider a homogenous isotropic solid : Consider a homogenous isotropic solid. Assume that all relevant properties do not depend on temperature and position within the solid. Derive the heat conduction (diffusion) equation in The rectangular coordinate system. Cylindrical coordinate system..
Consider a saturated clay layer : Consider a saturated clay layer of 4 m thickness on top of a deep layer of stiff sand. The clay has an initial porosity n=40%. Following a lowering of the water level in the clay, the clay porosity is reduced to 30%. What is the change of thickness S..
Piston-cylinder device with an initial pressure : Air with a mass of 0.5 kg, contained inside a piston-cylinder device with an initial pressure of 5 bar and initial volume of 0.1 m3, undergoes a thermodynamic cycle consisting of 3 processes as follows:
What do you mean by the term balanced diet : What do you mean by the term balanced diet? List out the steps involved in preparing a balanced diet.
The spacing of the bands be near the bottom of the vat : A cylindrical wooden storage vat has a 20 ft outside diameter. It is filled with 24 feet of brine with a specific gravity of 1.06. The wooden staves making up the vat are bound by flat steel bands evenly spaced vertically around the tank.
How long is the congressional review period : How many countries are negotiating the Trans-Pacific partnership wit the United States and how long is the Congressional review period before they make a final deal?
Specific work of the process and the final temperature : An ideal gas (MW = 26.0 lbm/lb·mol) undergoes a poly tropic process (with poly tropic index being 1.67) from an initial state of 6.9836 ft3/lbm and 60°F to a final volume of 0.86848 ft3/lbm. Show the process on a P-v diagram. Find the specific work o..
Spring-loaded piston-cylinder device is initially filled : A spring-loaded piston-cylinder device is initially filled with 0.13 lbm of an R-134a liquid-vapor mixture whose temperature is ?30°F and whose quality is 80 percent. The spring constant in the spring force relation F = kx is 37 lbf/in, and the pisto..
Power plant operates a regenerative rankine cycle : A power plant operates a regenerative Rankine cycle with one open feed water heater and has a net power output of 1x10^9 Btu/hr. When the steam exits the boiler it’s temperature is 1000°F and its pressure is 1400 psi. At the exit of the first stage o..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd