The solid circular aluminium rod has a diameter

Assignment Help Mechanical Engineering
Reference no: EM13710441

The solid circular aluminium rod has a diameter d=40 mm and can be subjected simultaneously to a torque T in the direction shown and to a tensile axial load P. The modulus of elasticity is E=73 Gpa, and the shear modulus G= 28 Gpa. (a) Determine the shear strain γxy that results if T=1.0kN.m and P=0. (b) For this torsion-only loading, determine the extensional strains εn and εt along the respective n and t directions

Reference no: EM13710441

Questions Cloud

What is its acceleration : Suppose an object changes it velocity from v = (30i + 4j) m/s to v = (-4i + 30j) m/s in 5 seconds. What is its acceleration
What is the spring constant : A 75 kg rock sits quietly on a spring, having displaced the end of the spring by 0.15 m.  What is the spring constant
Piston-cylinder assembly containing water : A piston-cylinder assembly containing water, initially a liquid at 500F, undergoes a process at a constant pressure of 20 lbf/in2 to a final state where the water is a vapor at 3000F. Kinetic and potential energy affects are negligible. Determine the..
Estimate how far does it trave : A ball is thrown with a velocity of 31m/scat and angle of 30degrees above the horizontal. How far does it travel if it is caught at the same height it was released
The solid circular aluminium rod has a diameter : The solid circular aluminium rod has a diameter d=40 mm and can be subjected simultaneously to a torque T in the direction shown and to a tensile axial load P. The modulus of elasticity is E=73 Gpa, and the shear modulus G= 28 Gpa.
Obtain what is the coefficient of kinetic friction : If the block comes to rest in 1.3m, what is the coefficient of kinetic friction between the block and the surface
The flue gases have the same variable specific heat as air : Calculate the percent energy distribution in a steam generator that goes into steam, losses to flue gases, refuse and heat losses. The steam generator receives 480 short tons of coal per day. The heating value of coal is 13,000 BtU/lb",. 375,000 Ib,j..
What average power must the motor supply : An advertisement claims that a certain 1200-kg car can accelerate from rest to a speed of 25 m/s in 8.0 s. What average power must the motor supply
What is the impulse provided to the baseball by the bat : A 5 1/8 oz baseball traveling at 89 mph rebounds off of a bat with a speed of 161 mph. The ball is in contact with the bat for roughly 10^-3 seconds. The incoming velocity of the ball is horizontal and the outgoing trajectory forms an angle of 33 deg..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  In all but a very few vehicles today crush or crumple zones

in all but a very few vehicles today crush or crumple zones are employed as a method to reduce energy transfer to the

  A projectile is fired at an angle of 62deg from the

a projectile is fired at an angle of 62deg from the horizontal with a velocity of 704 ftsec. if it lands 4.75 seconds

  Sketch the cycle indicating the isobars and the isochores

an ideal gas whose adiabatic exponent is equal to gamma undergoes a cycle consisting of two isochoric and two isobaric

  A 3 cm thick stainless steel thermal diffusivity 00000044

a 3 cm thick stainless steel thermal diffusivity 0.0000044 k16.3 initially at 500degc is suddenly exposed to convective

  The outer surface of a grill hood is at 47 degrees celsius

the outer surface of a grill hood is at 47 degrees celsius and the emissivity is 0.93. the heat transfer coefficient

  The room temperature yield strength of ni is 100mpa 15000

the room temperature yield strength of ni is 100mpa 15000 psi and furthermore sy diminishes about 5mpa for every 50

  Air flows steadily at rate of 04kgs through an air

air flows steadily at rate of 0.4kgs through an air compressor entering at 6ms with a pressure of 1 bar and specific

  Determine the speed va and angle ua at which the ball was

it is observed that the time for the ball to strike the ground at b is 2.5 s. determine the speed va and angle ua at

  Determine the torque t and power p that can also act

a solid shaft 200 mm in diameter rotates at f 20 revsec and is subjected to a bending moment of 21p kn.m. determine

  Let l19 cm and h244 cm if the system is released from rest

the uniform sphere b of radius r6cm and mass mb 5kg is rigidly attached to the uniform thin bar ab which is pinned at a

  Determine the maximum power that can be transmitted through

determine the maximum power that can be transmitted thru a stepped shaft rotating at 60 hz. knowing the radius of the

  Air as an idea gas is compressed from a state where the

air as an idea gas is compressed from a state where the pressure is 0.1 mpa and the temperature is 27oc to a state

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd