The second turbine exhausts at 480kpa to the regenerator

Assignment Help Mechanical Engineering
Reference no: EM13643935

A closed gas turbine unit uses neon as the working fluid. There are two stages of compression with intercooling from 480kPa and 290K to a maximum pressure of 2.75MPa with an intermediate pressure of 1149kPa. The regenerator has an effectiveness of 60% and delivers the neon to the high-temperature heat exchanger, where it is heated to 890K. There are two turbine stages, the first discharging at 1170kPa. Following the first turbine stage, a heat exchanger re-heats the neon temperature to 890K. The second turbine exhausts at 480kPa to the regenerator. All the expansion and compression processes are isentropic and using constant specific heats at room temperature, determine:

a. The compressor work per kilogram
b. The turbine work per kilogram
c. The heat added to the cycle per kilogram
d. The thermal efficiency
e. The power output for a neon flow rate of 45kg/s

Reference no: EM13643935

Questions Cloud

The influence of running on preventing heart attacks has : the influence of running on preventing heart attacks has been studied by a local runners club. the following twoshyway
Propose a sampling strategy for the supervisor how would : between quarterly audits a company checks its accounting procedures to detect problems before they become serious. the
If p waves are received at a seismic station 1 minute : an earthquake emits both s waves and p waves which travel at different speeds through the earth. a p wave travel 9000
Sketch a free-body diagram labeling the gravitational and : a beam resting on two pivots has a length of l 6.00 m and mass m 76.6 kg. the pivot under the left end exerts a
The second turbine exhausts at 480kpa to the regenerator : a closed gas turbine unit uses neon as the working fluid. there are two stages of compression with intercooling from
What is the 95 confidence interval for the mean turtle : an analysis of 25 sea turtles rescued indicates the average weight is 321.4 kg with a standard deviation of 73.8 kg.
If our eyes could see a slightly wider region of the : if our eyes could see a slightly wider region of the electromagnetic spectrum we would see a fifth line in the balmer
Water pressurized to 3 105 pa is flowing at 5 msec in a : water pressurized to 3 105 pa is flowing at 5 msec in a horizontal pipe which contracts to 13 its former area. what is
If the cards are to blur together into solid blocks of : a large group of football fans comes to the game with colored cards that spell out the name of their team when held up

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd