The rate of heat addition to the air by the heating coil

Assignment Help Mechanical Engineering
Reference no: EM13708508

In a heating/humidifying system moist air first flows through a heating coil and then through an air washer. The air enters the system at 55 °F dry-bulb temperature and 40 % relative humidity. The air exits the system at 90 °F dry-bulb temperature and 65°F thermodynamic wet-bulb temperature. The flow rate through the system is 2200 lbma/hr and the process occurs at a pressure of 29.921 in. Hg. Determine:

a. The dry-bulb temperature of the air as it exits the heating coil,

b. The rate of heat addition to the air by the heating coil,

c. The rate of moisture addition to the air by the adiabatic saturator

Reference no: EM13708508

Questions Cloud

Gold has an fcc crystal structure : Gold has an fcc crystal structure. The cell parameter (lattice constant) is 0.408 nm. 1) Determine the distance (d-spacing) between the [311] and [111] planes; 2) Sketch the [110] direction in the unit cell and determine the linear density of gold; 3..
Apply principle of the increase of entropy : Two same objects with the same initial temperature Ti have a constant specific heat capacity of Cp, now one installs a refrigerator in between these two and tries to lower one of the objects temperatures to T2.
How tall is the building : A ball thrown horizontally at 12.5m/ from the roof of a building lands 20.0mm from the base of the building. How tall is the building
Estimate how tall is the building that child is standing on : You are walking around your neighborhood and you see a child on top of a roof of a building kick a soccer ball. How tall is the building that the child is standing on
The rate of heat addition to the air by the heating coil : In a heating/humidifying system moist air first flows through a heating coil and then through an air washer. The air enters the system at 55 °F dry-bulb temperature and 40 % relative humidity. The air exits the system at 90 °F dry-bulb temperature an..
Estimate how much time does the man have : A cement block accidentally falls from rest from the ledge of a 70.0 -m-high building. How much time, at most, does the man have to get out of the way
Maximum inner diameter for the shaft for a yield strength : A shaft with a 2-inch outer diameter must deliver 5000 ft-lbs of torque. The shaft must be hollow and must simultaneously carry hydraulic fluid at an internal pressure of 30,000 psi. Assuming the shaft is closed-ended, and using the von Mises yield c..
Calculate its speed at launch : A dynamite blast at a quarry launches a rock straight upward, and 1.7 s later it is rising at a rate of 14 m/s. Calculate its speed at launch
Determine the power input to the compressor : Refrigerant 22 enters an insulated compressor operating at steady state as saturated vapor at -16oC with a mass flow rate of 1.5 kg/s. Refrigerant exits at 7 bar, 70oC. Changes in KE and PE from inlet to exit can be ignored. Determine: (a) the volume..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd