The pump draws 20 kw of power and operates at 50 efficiency

Assignment Help Mechanical Engineering
Reference no: EM13623905

Consider a pump that moves Q=0.1 m3/s of oil (S.G. = 0.8) from an open reservoir through a 10 cm diameter pipe. The pump draws 20 kW of power and operates at 50% efficiency. Determine (1) the gauge pressure (kPa) and (2) the total head of the fluid (m) immediately downstream of the pump.

Reference no: EM13623905

Questions Cloud

N is described by its state properties of temperature : n2 is described by its state properties of temperature -100 deg c and pressure 10.0 mpa. determine if it is
As the chain is raised assuming that the motor supplies a : a ships anchor chain is wrapped around a hollow steel drum of mass m 500 kg and radius r 0.5m. the drum is located on
Derive an expression for the building equation for the cstr : determine the concentration of a non-reactive tracer that was released as a pulse input if the flow in is 1.5 cms and
1 determine for each case whether the substance is a : 1 determine for each case whether the substance is a compressed liquid superheated vapor or saturated mixture using the
The pump draws 20 kw of power and operates at 50 efficiency : consider a pump that moves q0.1 m3s of oil s.g. 0.8 from an open reservoir through a 10 cm diameter pipe. the pump
Consider a cross flow of water saturated water that comes : consider a cross flow of water saturated water that comes at 20c with a velocity of 5 ms on the surface of a
A circular coil of wire consisting of 100 turns each of : a circular coil of wire consisting of 100 turns each of radius 8.0 cm carries a current of 0.40 a. what is the
Air can be assumed to be an ideal gas with a : a well-insulated tank contains 1 mole of air at 2 mpa and 673 k. it is connected via a closed valve to an insulated
The balance point of the cell in open circuit is 763 cm : potentiometer used for the determination of internal resistance of a 1.5 v cell. the balance point of the cell in open

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Finally if you assume the power plant operates on a carnot

a power plant generates 150 mw of electrical power. it uses a supply of 1000 mw from a geothermal source and rejects

  Determine the vertical velocity vo with which a ball must

determine the vertical velocity vo with which a ball must be thrown in order for the time of flight to the bottom of

  Determine the mass flow rate of hot water withdrawn from

the hot water needs of a household are met by a 60 l electric water heater whose heaters are rated at 1.6 kw. the hot

  The rigid gate oab of fig p258 is hinged at o andnbsprests

the rigid gate oab of fig. p2.58 is hinged at o andnbsprests against a rigid support at b. what minimum

  Determine the radius of the crank r

Determine the radius of the crank R and the speed n of a slider crank mechanism, used in a shaker table. It is required that the average speed of the table is 5 m/s, and the maximum absolute acceleration is 3000m/s^2. Assume ratio R/L=0.2

  Implementation costs and simple payback

Calculate energy savings, implementation costs and simple payback. You should be able to find some tips and calculations from the text book.

  Calculate the volume flow rate of water through the pipe if

a venturi meter has an inlet of 250 mm and a throat of 150 mm diameter. its coefficient of discharge is .985. calculate

  Write a paper on boyles law and describe compression and

write a paper on boyles law and describe compression and combustion stroke . also explain charless law and illustrate

  Determine the final density and temperature of the gas

natural gas at 70 f and standard atmospheric pressure of 14.7 psi is compressed isentropically to a new absolute

  A harmonic motion is expressed as xt 06cos18pit - pi6

a harmonic motion is expressed as xt 0.6cos18pit - pi6 where xt is measured in inches t in seconds and the phase angle

  The specific gravity of the solid particles is 27 for this

a sample of saturated clay from a consolidometer test has a total weight of 3.36 ib and a dry weight of 2.32 ib the

  What is the maximum useful work that can be produced per

what is the maximum useful work that can be produced per pound of saturated steam which enters a steady flow system at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd