The pressure in an air tank is able to support a water

Assignment Help Mechanical Engineering
Reference no: EM13630732

Q1) The pressure in an air tank is able to support a water column 15 meter high. Find the absolute air pressure in (PSI) if the local atmospheric pressure is 101 kPa. Take the density of water to be 1000 kg/m3.

Q2) A 10 m3 tank contains Oxygen (32 kg/kmol) at 7 bar and 33 C. How many cylinders could be filled from this tank if the cylinder capacity is 300 liter each? The initial pressure inside each cylinder is 0.5 bar and the required cylinder pressure after filling is 2 bar. Assume that the filling process is isothermal.

Q3) A piston-cylinder device contains steam (water vapor) at 3.5 MPa, and 300 °C. Initially, the volume of steam is 0.24 m3. Steam is cooled at constant pressure until it becomes dry saturated vapor. The piston is held in its position and the cooling continues until the cylinder contains water at 220°C. Draw the P- v diagram and determine (a) the mass of steam, (b) the properties of steam at the final state, and (c) the total heat rejected in MJ.

Q4) A 10 m3 tank contains Oxygen (32 kg/kmol) at 7 bar and 33 C. How many cylinders could be filled from this tank if the cylinder capacity is 300 liter each? The initial pressure inside each cylinder is 0.5 bar and the required cylinder pressure after filling is 2 bar. Assume that the filling process is isothermal.

Reference no: EM13630732

Questions Cloud

Water is flowing through a 23 cm diameter pipe with a : water is flowing through a 23 cm diameter pipe with a velocity of 11 ms. the viscosity of water is 8 x 10-3 nmiddotsm2.
How much is the velocity at the outlet for each case if the : for the piping diameter changes and flow directions shown below if the velocity at the input is 5 ms the initial
A log with a specific gravity of 067 is floating in water : a log with a specific gravity of 0.67 is floating in water. determine the percentage of the volume of the log that is
Calculate the rate of change of density drhodt in the : a gas station uses a 0.05 m3 tank to store air at 800 kpa absolute and 15c. the tank is equipped with a valve through
The pressure in an air tank is able to support a water : q1 the pressure in an air tank is able to support a water column 15 meter high. find the absolute air pressure in psi
Water at 15degc is to be discharged from a reservoir at a : water at 15degc is to be discharged from a reservoir at a rate of 18 ls using two horizontal cast iron pipes connected
After the collision the orange disk moves along a direction : two shuffleboard disks of equal mass one orange and the other yellow are involved in a perfectly elastic glancing
Ammonia enters the expansion valve of a refrigeration : ammonia enters the expansion valve of a refrigeration system at a pressure of 10 bar and a temperature of 248c and
Construct the physical model based on the following let the : a compactor is a press that is employed to crush bulky material into a smaller volume. the system shown uses a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd