User Account

All Pages

The outer diameter of this tube is 60 mm determine a the

Assignment Help Mechanical Engineering
Reference no: EM13605510

A tube with elastic modulus of 75 GPa is used to support a compressive load. It is required that this tube must not stretch more than 0.05% of its original length and the outer diameter of this tube is 60 mm. Determine a) the maximum normal stress in the rod, b) the minimum wall thickness for a load of 10 kN.

Reference no: EM13605510

Questions Cloud

It does this with air entering at 70 ms 500 c and 3 atm and : an air turbine is a continuous flow device that produces shaft power by expanding high pressure air. a particular air
Determine a the local atmospheric pressure and b the : in water at a depth of 7 m the absolute pressure is read to be 164 kpa. determine a the local atmospheric pressure and
First show all forces and reaction at the instant of : skydiver jumps from airplane they will accelerate rapidly at first but air resistance prevents them from falling faster
Determine the maximum weight of block c if block b is not : a 10-lb block b rests as shown on a 20-lb bracket a. the coefficients of friction are us0.3 and uk0.25 between block b
The outer diameter of this tube is 60 mm determine a the : a tube with elastic modulus of 75 gpa is used to support a compressive load. it is required that this tube must not
If the plane starts to level off at t 40 s determine at : the flight path of a jet aircraft as it takes off is defined by the parametric equations x 1.25 t2 and y 0.03 t3
If the coefficient of kinetic friction between the 50-kg : if the coefficient of kinetic friction between the 50-kg crate and the ground is .3 determine the distance the crate
Which of the following butt-weld preparations is usually : which of the following butt-weld preparations is usually the most susceptible to lack of sidewall fusion during the
The coefficient of friction of the metal against the dies : a cylinder of metal that is originally 100mm tall and 50mm in diameter must be open die forged to a height if 50mm. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  You are an industrial hygienist for a large distributor of

you are an industrial hygienist for a large distributor of industrial compressed gases who was evacuated to baton rouge

  A four-cylinder four-stroke 22 liter gasoline engine

a four-cylinder four-stroke 2.2 liter gasoline engine operates on the ideal otto cycle with a compression ratio of 10.

  Determine the radius of curvature of the path of the package

package is dropped from the plane which is flying with a constant horizontal velocity of vA = 150 ft/s at a height h = 1500 ft. Determine the radius of curvature of the path of the package just after it is released from plane at A.

  Determine the initial and final pressures

Friction between the piston and the cylinder wall can be neglected. For the air, determine the initial and final pressures, in kPa, and the work, in kJ.

  Compute the position of the quasi-fermi

calculate the position of the quasi-Fermi levels for electrons and holes with respect to the intrinsic level (assume that ni=1.5x10^10cm^-3).

  Evaluate the maximum height reached by the sphere

Evaluate the maximum height reached by the sphere, and the distance traveled by the block.

  How many engagement points on the flywheel

a full revolution press has 100 rpm flywheel rotation.it has two handed trip devices mounted 20 inches from point of operation how many engagement points on the flywheel would be nessary to make this machine safe?

  Determine the maximum axial compressive force

A short 60-mm-diameter circular bar is made of a material for which the maximum safe compressive stress is 80 MPa and the maximum safe shearing stress is 30 MPa. Determine the maximum axial compressive force that can be safely applied.

  Find out the exit temperature

Determining the Exit Temperature and Power Input of Air through a Compressor, Air at 150Pa and 310K enters a compressor of inlet diameter 2cm. The Compressor raises the pressure to 3.5 times the inlet pressure

  Baseline validationdetermine the natural frequencies of the

baseline validationdetermine the natural frequencies of the system. for the baseline system i get natural frequencies

  A tensile member of 2024-0 aluminum alloy used for aircraft

a tensile member of 2024-0 aluminum alloy used for aircraft fuselage had an original cross-sectional area of 4.0square

  Boom ab is held in the position shown by three cables

boom ab is held in the position shown by three cables. knowing that the tensions in cables ac and ad are 4 kn and 5.2

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd