The only question is the strength of the block in

Assignment Help Mechanical Engineering
Reference no: EM13620503

Limestone blocks approximately 8 in. wide by 14 in. long by 6 in. high are sometimes used in constructing dry stacked walls. If the stability of the walls is not an issue and the only question is the strength of the block in compression , how high could blocks be stacked if the limestone has a compressive strength of 4000 psi and a density of 135lb per cubic foot?

Reference no: EM13620503

Questions Cloud

The chain and lever attached to the gate have negligible : a gate with a circular cross section is held close by a lever 1 m long attached to a buoyant cylinder. the cylinder is
If r 12 cm m 370 g and m 40 g below find the speed of : if r 12 cm m 370 g and m 40 g below find the speed of the block after it has descended 50 cm starting from rest.
Your friend is considering adding one additional stock to a : your friend is considering adding one additional stock to a 3-stock portfolio to form a 4-stock portfolio. she is
What is the maximum speed of a truck that you are sure will : on a trip to the colorado rockies you notice that when the freeway goes steeply down a hill there are emergency exits
The only question is the strength of the block in : limestone blocks approximately 8 in. wide by 14 in. long by 6 in. high are sometimes used in constructing dry stacked
Aparticle of mass m 424times105 evc2 moves in a : a particle of mass m 4.24times105 evc2 moves in a three-dimensional box with edge lengths l10.54 nm l21.08 nm and
The average length of a new born baby is 20 inches with a : the average length of a new born baby is 20 inches with a standard deviation of 1 inch.if n100 what is the mean of the
Suppose a dividend of 125 was paid the stock has a required : suppose a dividend of 1.25 was paid. the stock has a required rate of return of 11.2 and investors expect the dividend
A crate is pulled by a hoist a distance of 34m across the : a crate is pulled by a hoist a distance of 3.4m across the flat truck bed in 8 seconds. determine the work done in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The tank is allowed to exchange heat with the surroundings

a tank of compressed air is at 40 degrees c and 10 atm. 1 third of the gas is removed for inflating a car tire. the

  What should have been the weight density pg of this mud in

at a depth of 18360ft fillers on the deepwater horizon encountered fluid at a reservoir pressure of 8900 psia. in order

  This means that the crystal structure of a cu-ni alloy

cu and ni form a substitutional solid solution. this means that the crystal structure of a cu-ni alloy consists of ni

  Estimate the theoretical fracture strength of a brittle

estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation

  Explain the following terms with respect to 4-storke cycle

explain the following terms with respect to 4-storke cycle internal combustion engines strokebore ratio piston

  Calculate the force required to hold the gate closed

the gate in the is hinged at H.the gate is 2 m wide and normal to the palne of the diagram.calculate the force required to hold the gate closed.

  What is the electrical power available

You are designing a remote-area power supply based on a miniature wind turbine that is 20% efficient. Meteorological data indicates an average wind speed of 24 km/h at an air temperature of 10oC and pressure of 0.9 atm. The rotor has a diameter of..

  Effect of material hardness

On a single graph, plot "Hardness" as the ordinate versus "Aging Time" as the abscissa for each aging temperature - Discuss the effect of aging time and temperature on the effect of material hardness.

  What is the total energy released by burning the mass of

over a period of time a car engine burns 0.01kg of fuel equivalent to supply of qh from a high temperature reservoir at

  Calculate the spindle rpm for this operaion calculate the

for a turning operations you have selected an hss tool and turning a hot rolled free machining steel bhn 300. your

  Determine the stress in the wires

a 1.5 ton crate is hoisted by three steel wires. each wire is 1/4 in. in diameter and each carries one-third of the load. determine the stress in the wires.

  Solve for the pressure of a gas using both equations

Solve for the pressure of a gas using both equations at a temperature of 400K and a molar volume of 1x 10-4 m3/mol. For the van der Waals EOS, use parameters of a= 4.1x10-1 (m3/mol)2 Pa, and b=4.3x10-5 m3/mol.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd