User Account

All Pages

The model simulation is ran in parallel with the actual

Assignment Help Mechanical Engineering
Reference no: EM13624366

When using LabView, applying a voltage to the DC motor and examining its angular rate can be done using the Modeling Vurtual Instrument. The model simulation is ran in parallel with the actual system to allow for model tuning and validation. Do you expect the motor to behave exactly as the model suggests? IF not, list three factors that could cause this.

Reference no: EM13624366

Questions Cloud

A laboratory glass bottle used in laboratory studies of : a laboratory glass bottle used in laboratory studies of hypoxia contains gas of the following composition expressed as
A very long cylinder of charge has a radius r and charge : a very long cylinder of charge has a radius r and charge density pcr2 where c is a constant.a. if the total charge on a
Lt y1 y2 y3 and y4 constitute a random sample of size n : let y1 y2 y3 and y4 constitute a random sample of size n 4 from a bernoulli population with parameter p. a determine
An apparatus for measuring thermal conductivity employs an : an apparatus for measuring thermal conductivity employs an electrical heater sand- wiched between two identical samples
The model simulation is ran in parallel with the actual : when using labview applying a voltage to the dc motor and examining its angular rate can be done using the modeling
Consider a 300 mm x 300 mm window in an aircraft for a : consider a 300 mm x 300 mm window in an aircraft. for a temperature difference of 80oc from the inner to the outer
The mean points obtained in an aptitude examination is 124 : the mean points obtained in an aptitude examination is 124 points with a variance of 400. what is the probability that
The incoming air velocity is 100 ms the air density and : consider airflow past a sphere of diameter 5 cm. the incoming air velocity is 100 ms. the air density and temperature
Assume steady-state one dimensional heat conduction through : assume steady-state one dimensional heat conduction through the symmetric shape shown. assuming that there is no

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the turbine has an efficiency of 90 calulate the turbine

in a steam power plant 6000 kgs of steam enters the turbine at 8 mpa 480 degree c and expands to 0.7 mpa. if the

  Determine the dimensions of the lowest cost container

design an outside storage facility for methane gas ch4. 110 kg is the maximum mass of methane to be stored at this

  Despite the limits of this type of system ie low work

refrigerant 134a is the working fluid in an organic rankine cycle. saturated vapor at 60degc enters the turbine and the

  Determine the magnitude of the average friction force

the 3.25-kg collar shown below is attached to a spring and released from rest at a. the collar then travels downward a

  Calculate the thermal efficiency of this cycle

The Brayton cycle shown in figure 6.41 operates using CO2 as a working fluid with compressor and turbine isentropic efficiencies of 1.0. Calculate the thermal efficiency of this cycle when the working fluid is modeled.

  Calculate the velocity and acceleration of collar a

In the position shown, the angular velocity and the angular acceleration of the rod AB are 4 rad/sec and 6 rad/sec2, respectively, both counterclockwise. For this instant calculate the velocity and acceleration of collar A. ( AB = 600 mm)

  The material hoist and the load have a total mass of 900 kg

the material hoist and the load have a total mass of 900 kg and the counterweight c has a mass of 150 kg. at a given

  Find i the maximum pressure shown by a gauge on the cooker

2 kg of water at 10oc and atmospheric pressure are placed in a pressure cooker and heated until the water boils at

  Determine the largest couple moment m

The uniform 6-kg slender rod rests on the top center of the 3kg block. If the coefficients of static friction at the points of contact are ua=.4 and ub=.6, and uc=.3, determine the largest couple moment M which can be applied to the rod without ca..

  Accounting for the change is void fraction does this

liquid chromatography lc flow can be model as a packed bed and is described by the ergun equation. lc systems are often

  Find the value of the reduced volume both fluids would have

assume that oxygentc 154.6k pc 5.046 x 106 pa and vc 7.32x10-5 m3mol and water tc 647.3kpc 2.205 x 107 pa and vc 5.6

  A bucket of mass 20kg is whirled in a vertical circle of

a bucket of mass 2.0kg is whirled in a vertical circle of radius 1.1m. at the lowest point of its motion the tension in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd