The maximum torque is tooccur

Assignment Help Electrical Engineering
Reference no: EM131008511

1.A 220 V, 3-phase, 4-pole, 50 Hz inductor motor of wound rotor type is supplied at ratedvoltage and frequency. The stator resistance, magnetizing reactance, and core loss arenegligible. The maximum torque produced by the rotor is 225% of full load torque and itoccurs at 15% slip. The actual rotor resistance is0.03 / phase. ?The value of externalresistance (in Ohm) which must be inserted in a rotor phase if the maximum torque is tooccur at start

Reference no: EM131008511

Questions Cloud

How can the width of this interval be reduced : Suppose the confidence interval obtained in part a is too wide. How can the width of this interval be reduced? Discuss all possible alternatives. Which alternative is the best
A shunt machine has armature : Question 1) A shunt machine has armature and field resistance of 0.04 ohm and 100 ohm respectively. When connected to a 460 V d.c. supply and driven as a generator at 600 rev/min, it delivers 50 kW. Calculate its speed when running as a motor and tak..
Power of the test the inspectors conduct : Quality control, part 2. Consider again the task of the quality control inspectors in Exercise 70. a) In this context, what is meant by the power of the test the inspectors conduct?
Prepare journal entries to record the effects on shannon : Prepare journal entries to record the effects on Shannon's accounting records at December 31, 2011, for each of the items described above. Show all calculations.
The maximum torque is tooccur : 1.A 220 V, 3-phase, 4-pole, 50 Hz inductor motor of wound rotor type is supplied at ratedvoltage and frequency. The stator resistance, magnetizing reactance, and core loss arenegligible. The maximum torque produced by the rotor is 225% of full load t..
Which of the graph types introduced in this section is used : The accompanying graphical display appeared in USA Today (October 22, 2009). It summarizes survey responses to a question about whether visiting social networking sites is allowed at work. Which of the graph types introduced in this section is use..
Dc motor operates at its rated terminal voltage : 1.A shunt-connected DC motor operates at its rated terminal voltage. Its no-load speed is200 radians/second. At its rated torque of 500 Nm, its speed is 180 radian/second. Themotor is used to directly drive a load whose load torque TL depends on its ..
Find what percentage of the observations fall in intervals : A sample of 3000 observations has a bell-shaped distribution with a mean of 82 and a standard deviation of 16. Using the empirical rule, find what percentage of the observations fall in the intervals x-bar ± 1s, x-bar ± 2s, and x-bar ± 3s
What role would random assignment play in this determination : The types of grasslands to be used include undisturbed native grasses, managed native grasses, undisturbed nonnative grasses, and managed non- native grasses. You are allowed a plot of land 500 meters square to study. Explain how you would determi..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much pressure in atmospheres must the submersible

Titan has numerous hydrocarbon lakes containing a mix of methane and ethane in unknown proportions. A small submersible vehicle will exlpore Kraken Mare, the largest lake.

  Determine the phase shift in each case at 50 and 75hz

a second instrument is required to measure the input signals up to 100Mz with an amplitude inaccuracy of less than 1% calculate the natural frequency requirements, if the damping retios are 0.3 and 0.6 respectively.

  Find secondary current and operating pf of each transformer

Two parallel connected 10 kV to 120 V 60 Hz single phase transformers supply a varying load. When the total secondary load current is 250 A at 0.85 PF lagging, determine the secondary current and operating PF of each transformer.

  What impact will the have on the cellular geometry

show that if n=4, a cell can be split into four smaller cells, each with half the radius and 1/16 of the transmitter power of the original cell. If extensive measurements show that the path loss exponent is three

  From what distance must the electron be red

From what distance must the electron be red if it is to just fail to strike the plate?

  Find the modulation index and percentage of modulation

An AM transmitter radiates 9 kW of power when the carrier is unmodulated and 10.125 kW when the carrier is sinusoidally modulated. Find the modulation index, percentage of modulation.

  Describe how would design a gray code counter without vhdl

Explain why the low value (0) for the 'output' of a digital logic gate is lower than the low value for the 'input' of a digital logic gate (This is the case for CMOS and Bipolar logic). Look at a specsheet.

  How does it operate in each of the situation

Extension cords which are designed to carry heavier loads are generally larger in diameter than those which are not. Is this just a matter of adding more insulation, or is there a physical principle at work causing the larger diameter? Explain.

  Describe a specific measured point on the curve

At the point you can check a point or two on the V-I curve and confirm that the plot is equivalent to the linear plot in Part 1. Describe a specific measured point on the curve and what it represents.

  How many bits are required to represent the decimal

how many bits are required to represent the decimal numbers in the range from 0 to 999 using straight binary code?

  Calculate the temp when the piston just lifts off the stop

Heat is added until the final volume is twice the initial volume. Assume that Helium behaves as an ideal gas. Use the table provided to determine the specific heats of helium and determine the following.

  Determine magnitude of line to-line voltage at load terminal

A balanced delta connected load of 15 + j18 ohms per phase is connected at the end of a three-phase line. The line impedance is 1 + j2 ohms per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 V rms.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd