User Account

All Pages

The isentropic efficencies of the turbine and the pump are

Assignment Help Mechanical Engineering
Reference no: EM13632686

A steam power plant operates on the reheat rankine cycle between 15 mpa and 10 kpa. System enters the high pressure turbine at 15 Mpa and 500c at rate of 12 kg/s. steam is then reheated at constant pressure to 500c and 4 Mpa befer it expands in the low pressure turbine. The isentropic efficencies of the turbine and the pump are 85% and 90% respectively. Steam leaves the condeser as saturated liquid.

Detrmine

1- Net power out put

2- Thermal efficiency

Reference no: EM13632686

Questions Cloud

A 1050 hot-rolled steel of diameter 300mm has an ultimate : a 1050 hot-rolled steel of diameter 300mm has an ultimate tensile strength of sut724mpa that is hot-rolled is exposed
Determine the height of the hill above the valley floor : a car sits on the side of the road trying to sit out a blizzard. a passing truck skids into the stationary car sending
Water at 20c flows through at 10cm inner dyameter pipea : water at 20c flows through at 10cm inner dyameter pipe.a static pressure tap of a pilot tube at a cross section
A vertical glass tube of length l 128 m is half filled with : a vertical glass tube of length l 1.28 m is half filled with a liquid at 20 c. how much will the heigh of the liquid
The isentropic efficencies of the turbine and the pump are : a steam power plant operates on the reheat rankine cycle between 15 mpa and 10 kpa. system enters the high pressure
It is estimated that in the united states population 250 : it is estimated that in the united states population 250 million there is one electric clock per person with each clock
Draw the tree for red cats decision problem and determine : the management of red cat computers was considering launching a new product called the tiger 100. the problem was that
Dangerous dan a scottish bricklayer throws a brick as hard : dangerous dan a scottish bricklayer throws a brick as hard as he can at 100 ms srraight up in the air. what is the
The average number of mosquitos in a stagnant pond is 70 : the average number of mosquitos in a stagnant pond is 70 per square meter with a standard deviation of 8. if a sample

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  5 bolts are made of low carbon steel with a yield point in

5 bolts are made of low carbon steel with a yield point in shear of 19200 psi. the bolts are 38 inch in diameter and

  The mechanical effficiency of the system is 80 what is the

it takes 15 seconds to raise a 1200 kg car and the supporting 300 kg hydraulic lift platform to a height of 2.8 m. the

  Determine the number of revolution by the disk

a disk has a mass of 4kg and a radius of 90mm, it is at rest when it is placed in contact with the belt, which moves with a constat speed (v =15m/s). knowing that friction is .25 between the disk and the belt. Determine the number of revolution by..

  A 31-l electric radiator containing heating oil is placed

a 31-l electric radiator containing heating oil is placed in a 48-m3 room. the room and the radiator oil are initially

  Calculate the maximum mass flow rate at the inlet condition

a refrigerant 134a at 140 kpa and -10 degree celcius is compressed by an adiabatic 16kw compressor to an exit state of

  What must be its minimum yield strength

A steel alloy to be used for a spring application must have a modulus of resilience of at least 2.07 MPa (300 psi). What must be its minimum yield strength?

  Air at 50 psia and 90 f flows at the rate of 16 lbms

air at 50 psia and 90 f flows at the rate of 1.6 lbms through an insulated turbine. if the air delivers 11.5 hp to the

  Determine the volume of 10 kg of carbon dioxide vapor at

the surface pressure of venus is about 90 bar and the surfacetemperature is ap-proximately 880 degrees f. the

  Determine the final pressure 8 b was the compression

the adjoining figure illustrates a piston-cylinder arrangement. this cylinder contains helium at 21oc and 1.379 mpa.

  The spring has squared and ground ends and is made from

a helical compression spring is required to provide a minimum force of 80n at installation and have a working

  For air flowing in a converging-diverging nozzle the

for air flowing in a converging-diverging nozzle the pressure and temperature at the inlet are 14.7 psia and 70degf. at

  The pliers shown in the figure of the book are used to

the pliers shown in the figure of the book are used to grip a 0.3-in.-diameter rod. knowing that two 60-lb forces are

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd