User Account

All Pages

The intention is to draw air from the receiver during the

Assignment Help Mechanical Engineering
Reference no: EM13631377

A stoped out area with a volume of 20000 m3 is to be used as a receiver. It is to be charged to an absolute pressure of 1600 kPa during off shifts. The intention is to draw air from the receiver during the 4-hour drilling shift until the absolute pressure drops to 800 kPa. What is the rate at which the main air supply can be boosted during this period? Air temperature is 32°C, gas constant for air R=287 J/kgK.

Reference no: EM13631377

Questions Cloud

What constant force must be exerted on the rope to bring : a 150 kg merry-go-round in the shape of a uniform solid horizontal disk of radius 1.50 m is set in motion by wrapping a
Determine the dynamic viscosity of flow if the pressure : determine the dynamic viscosity of flow if the pressure drop of a fluid running with a flow rate of 880 mm3s through a
A non-uniform steady incompressible flow is observed to : a non-uniform steady incompressible flow is observed to have a velocity of 15ms at a point where the cross-sectional
Lght of wavelength 671 nm is incident on a single slit : light of wavelength 671 nm is incident on a single slit. the central bright fringe is 2.60 cm wide on a flat screen
The intention is to draw air from the receiver during the : a stoped out area with a volume of 20000 m3 is to be used as a receiver. it is to be charged to an absolute pressure of
A thin layer of oil of refractive index 118 is spread on : a thin layer of oil of refractive index 1.18 is spread on the surface of water n1.33. if the thickness of the oil is
Determine if the small diameter can be further reduced in : in order to accommodate a bearing on an 80mm diameter shaft it is suggested that it be reduced in diameter to 65 mm
The interference pattern shows a peak at the center of the : two slits separated by a distance of d 0.185 mm are located at a distance of d 2.06 m from a screen. the screen is
A 356 mm diameter main services a section of a mine and : a 356 mm diameter main services a section of a mine and carries 4.8 kgs of compressed air at peak periods. if the main

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The system is then heated while the pressure is held

consider a piston-cylinder system containing 0.1 kg of water. initially the volume of the system is 0.0125m3 while the

  If the tube elongates 3mm and its circumfrence decreases

a thin-walled tube is subjected to an axial force of 40 kn. if the tube elongates 3mm and its circumfrence decreases

  What is the change in enthalpy in kjkg of oxygen as its

what is the change in enthalpy in kjkg of oxygen as its temperature changes from 150 to 200oc? is there any difference

  Three shopping carts are initially stationary on a slope

three shopping carts are initially stationary on a slope the friction in the wheels allowing them to stay still. a

  A vertical piston-cylinder device initially contains 025 m3

a vertical piston-cylinder device initially contains 0.25 m3 of air at 600 kpa and 300degc. a valve connected to the

  F reheat temperature so the turbine output is

a smaller power plant produces steam at 3 mpa 600 c in the boiler. it keeps the condenser at 45 c by transfer of 10 mw

  In a preliminary design for a mail-sorting machine parcels

in a preliminary design for a mail-sorting machine parcels moving at 2 fts slide down a smooth inclined ramp and a

  The 20degc surroundings experience an entropy increase of

consider an r-134a compressor on a refrigeration system. if the refrigerant enters as saturated vapor at 200 kpa 0.03

  A model 110 of scale of a tractor-trailer rig is tested in

a model 110 of scale of a tractor-trailer rig is tested in a wind tunnel. the cross section area of the model is 0.1 m2

  As the load on the motor is increased the developed torque

a 115-v shunt motor develops 21 ib-ft when the armature current is 12 a. as the load on the motor is increased the

  Find the reversible amount of of work per unit mass find

the air with constant properties in a steady adiabatic flow enters a system at a pressure of 10 bars and 500k with a

  Boiling water flows through thin-walled copper tubes in a

boiling water flows through thin-walled copper tubes in a cross-flow heat exchanger and atmospheric air flows across

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd