The horizontal distance between the point

Assignment Help Civil Engineering
Reference no: EM13534535

The elevtion of M is 875 . a transit was set at point M and a leveling rod was held vertically at point N. the horizontal cross line of the telescope was inclined so the reading of the horizontal cross line on the rod was 12 ft. the horizontal distance  between the point is 250 ft if the instrument is 5.25 ft above point  M and the reading of the vertical limb is 2 degree, the elevation of N is wich one is correct is A873.42 or B880.38 or is C889.83 or is D877.38 wich one is correct?

Reference no: EM13534535

Questions Cloud

Determine the ground clearance of an overhead : Determine the ground clearance of an overhead electrical cable.surveyor B is positioned directly under the cable(surveyor B's position can be checked by his sighting past thesting of a plumb bob,held in his outstreched hand
Determine analytically whether or not it is linear : To prove that a system islinear or time-invariant, the property must be demonstrated for all possible input/output pairsand all delays. On the other hand, to prove that a system is not linear or not time-variant,the property can be demonstrated with ..
Determine the prism constant : A 100 ft cut steel tape was used to check the layout of a building wall. the rear surveyor held 42 ft while the head surveyor cut 0.33 ft. what is the distance measured?
How much must the temperature of the ring be increased : A steel ring of internal radius 499.8 mm is to be shrink-fitat normal (room) temperature over a rigid cylinder of radium r =500 mm
The horizontal distance between the point : The elevtion of M is 875 . a transit was set at point M and a leveling rod was held vertically at point N. the horizontal cross line of the telescope was inclined so the reading of the horizontal cross line
How are you to tell what the reynols number is : A rectangular concrete channel 4m wide on a slope of 0.002 is designed to carry water(T = 10 C) at discharge rate 25m^3/s. Estimate the uniform flow depth for these conditions?
How do you find this answer : A 14in diameter pipe pile is driven 50ft into a dry loose sandwhose unit weight is 105 pcf. The angle of internal frictionis 33 degrees. Compute the safe axial downward loading
What will be the grade elevation at station : The grade elevation at station 25+00 is to be 946.52 ft. What will be the grade elevation at station 34+86.20 if the grade linerises at the rate of 1.785% between these two points?
Find the percentage of aceticacid ionized in the solution : One liter of a solution is made by adding 3grams of acetic acid (HAc) to distilled water. The molecular weightof acetic acid is 60.052. The acid dissociation constant for aceticacid

Reviews

Write a Review

Civil Engineering Questions & Answers

  A small package is deposited by the conveyor belt onto the

a small package is deposited by the conveyor belt onto the 30 ramp at a with a velocity of 0.8 ms.nbspcalculate the

  Determine the values of theta dot and theta dot at instant

The plate OAB forms an equilateral triangle which rotates counterclockwise with increasing speed about point O. If the normal and tangential components of acceleration of the centroid C

  Determine the pressure at stagnation point on the nose

determine the pressure at stagnation point on the nose of the airplane. also determine the manometer reading h for the manometer attached to the static pressure tap within the test section of the wind tunnel if the air velocity

  Which would require less wood and by what percentage

An engineer is to design a channel lined with planed wood to carry 2 m3/s of water on a given slope. The channel cross section can be either a 90 degree triangle or a square. Which would require less wood and by what percentage

  Determine the modulus of elasticity and proportional limit

A tension specimen has a gauge length of 8 inches and a diameter of .505 inches. A load of 9580 pounds was found to develope a stress in the specimen equal to the proportional limit of materials. ( assume that the proportional limit and the yield ..

  Determine the approximate drag coefficient for the parachute

A 5-m-diameter parachute of a new design is to be used to transporta load from flight altitude to the ground with an average verticalspeed of 3 m/s. The total weight of the load and theparachute is 200 N. Determine the approximate dragcoefficient for..

  Find number of completely mixed chlorine contact chambers

Determine the number of completely mixed chlorine contact chambers each having a detention time of 30 min that would be required in a series arrangement to reduce the bacterial count of a treated effluent form 10^6 to 14.5 organisms/mL

  Explain how to calculate the mass flowrate in methane

Assuming the resulting hole acts like an isentropic converging nozzle with a throat diameter of 0.08 cm, calculate the mass flowrate in kg/s of methane that initially escapes from the tank.

  What are the possible combinations of inflow and outflow

what are the possible combinations of inflow and outflow of water in the tank in a given day. if the water level in the tank is 7ft from the bottom at the start of day, what are the possible water levels in the tank at the end of the day.

  How many grder hours will be required to accomplish the job

A motor grader will require 2 pases at 3 mph., 2 pases at 4 mph., and 2 passes at 5.5 mph. to accomplish the work How many grder hours will be required to accomplish this job if the job efficiency factor is 0.75.

  Explain how to determine the max height of a brick wall

Assuming a density of 120/ft^3 for masonry brick work, determine the max height of a brick wall if the allowable compressive stress is limited to 150/in^2 and the brick is a) 4" wide b) 6" wide.

  What is porportion of potential energy head at crosssection

if a pipeline is horizontal, what is the porportion of the potential energy head at the upstream crossection that is changed to kinetic energy head at the downstream crossesction

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd