The heater considered is a natural gas furnace whose

Assignment Help Mechanical Engineering
Reference no: EM13609145

You are asked to design a heating system for a swimming pool that is 2 m deep, 25 m long, and 25 m wide. Your client desires that the heating system be large enough to raise the water temperature from 20 to 30°C in 3 h. The rate of heat loss from the water to the air at the outdoor design conditions is determined to be 960 W/m2, and the heater must also be able to maintain the pool at 30°C at those conditions. Heat losses to the ground are expected to be small and can be disregarded. The heater considered is a natural gas furnace whose efficiency is 80 percent. What heater size (in kW input) would you recommend to your client?

Reference no: EM13609145

Questions Cloud

A 2250 l tank contains 5682 kg of steam at 5 bar determine : a 2250 l tank contains 5.682 kg of steam at 5 bar. determine the temperature and z compressibility of steam using a.
A company has limited machine hours available for : a company has limited machine hours available for production and must decide which of its four products to produce and
He company expects to sell about 35 of its merchandise for : the treasure of unisyms company has accumulated the following budget information for the first two months of the coming
Wilson owned equipment with an estimated life of 10 years : wilson owned equipment with an estimated life of 10 years when it was acquired for an original cost of 80000. the
The heater considered is a natural gas furnace whose : you are asked to design a heating system for a swimming pool that is 2 m deep 25 m long and 25 m wide. your client
The company expects to sell about 35 of its merchandise for : the treasure of unisyms company has accumulated the following budget information for the first two months of the coming
Assume that 350 kjkg of energy must be removed by heat : for each kw of power input to an ice maker at steady state determine the maximum rate that ice can be produced in kgs
If a company issues common stock with no par- or : if a company issues common stock with no par- or stated-value then the journal entry for an ipo initial public offering
A company has a balance of 300000 in its common stock : a company has a balance of 300000 in its common stock account. the par-value of the common stock is 10share. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the angle through which end d of shaft cd rotates

In the gear-and-shaft system shown, the shaft diameters are dab= 2 in. and dcd=1.5 in. Knowing that G = 11.2 x10^6 psi, determine the angle through which end d of shaft cd rotates.

  Calculate the transverse modulus of the peek

calculate the transverse modulus of the peek/carbon fiber composite with 30% volume fraction by tow method. the modulus of peek is 3.8 GPa and the modulus of the carbon fiber is 400GPa. assume the reinforcing factor.

  Find the complete initial and final states for the

find the complete initial and final states for the following processes t p v h u s and phase involving simple

  What is the volume change when 2 kg of h2o at 68 mpa and 93

what is the enthalpy change needed to change 3 kg of liquid water at 0 c to steam at 0.1 mpa and 150 c? b. what is the

  Determine the work and heat transfer for the process

Two kilograms of Refrigerant134a, initially at 2 bar and occupying a volume of 0.12 m3, undergoes a process at constant pressure until the volume has doubled. Kinetic and potential energy effects are negligible. Determine the work and heat transfe..

  A charged particle with a charge-to-mass ratio of qm 57

a charged particle with a charge-to-mass ratio of qm 5.7 108 ckg travels on a circular path that is perpendicular to a

  Air is compressed under steady flow conditions see figure

air is compressed under steady flow conditions see figure q3. the power input to the compressor is 3 kw. during the

  What steel specification suitable for structural application

Find the stress in both members shown below and what steel specifications (types of steel) are suitable for structural applications?

  What is the elastic modulus of the material

A beam of span 600mm has a load of 1 kg and deflects by 0.55mm its width is 25.4mm and depth is 6.7mm what is the elastic modulus of the material?

  Solve the heat diffusion equation to find tx and find the

heat is generated uniformly inside a 20-mm thick plane wall at a rate of 20000 wm3. the thermal conductivity of the

  Given an aerodynamic body you have learned in aerodynamics

given an aerodynamic body you have learned in aerodynamics and flight mechanics how to apply the numerical source panel

  What are the four basic families of shape-production process

what are the four basic families of shape-production processes? Cite one advantage and one limitation of each family.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd