The heat transfer takes place through a boundary

Assignment Help Mechanical Engineering
Reference no: EM13634095

A mixing chamber operated at 300 kPa pressure and is designed to mix a stream of steam with a stream of water. Steam at a temperature of 160 C enters the mixing chamber, where it is mixed with water that flows in at a temperature of 20 C and a mass flow rate of 5 kg/s. At the exit of the mixing chamber the mixture has a temperature of 70 C. The mixing chamber is not fully insulated, so that it loses heat to the surroundings at a rate of 40 kW. The heat transfer takes place through a boundary temperature of 25 C. Calculate: a) the mass flow rate of steam, and b) the rate of entropy production.

Reference no: EM13634095

Questions Cloud

Determine the maximum axial compressive load p that can be : a w254x33 structural steel e200gpa section is used for a column with an actual length of 6m. the column can be
An astronaut is rotated in a horizontal centrifuge at a : an astronaut is rotated in a horizontal centrifuge at a radius of 7.5 m. a what is the astronauts speed if the
On each visit the weight of sand you take home measured in : 1 every time you go to a beach for vacation you take home a little sand to keep as a souvenir. over your lifetime you
A jogger runs 100 m due west then changes direction for the : a jogger runs 100 m due west then changes direction for the second leg of the run. at the end of the run she is 175 m
The heat transfer takes place through a boundary : a mixing chamber operated at 300 kpa pressure and is designed to mix a stream of steam with a stream of water. steam at
Calculate the mass of silver chloride agcl and dihydrogen : calculate the mass of silver chloride agcl and dihydrogen monosulfide h2s formed when 85.6 g of silver sulfide ag2s
A manufacturer of disk drives for notebook computers wants : a manufacturer of disk drives for notebook computers wants a mtbf of at least 50000 hours. recent test results for 15
A 1600 kg car is pulling a 375 kg trailer together the car : a 1600 kg car is pulling a 375 kg trailer. together the car and trailer have an acceleration of 2.15 ms2 directly
Protein a has a binding site for glucose with a kd of : protein a has a binding site for glucose with a kd of 10-5m.protein b has a binding site for glucose with a kd of 10-7

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The premissible stresses in the key are 55 nmm2 in shear

a belt pulley is fastened to a 75 mm shaft running at 360 rpm by means of a key 18 mm wide and 125 mm long. the

  A 3 cm thick stainless steel thermal diffusivity 00000044

a 3 cm thick stainless steel thermal diffusivity 0.0000044 k16.3 plate initially at 500degc is suddenly exposed to

  Explain with clear reference to structural mechanisms and

magneto is seeking to produce a new helmet using a deep drawing process in which a sheet of 3103 aluminum will be

  Determine steam enters a the velocity at the exit in ms b

consider a horizontal pipe of diameter 20 cm. steam enters the pipe as a saturated vapor at 0.5 mpa with a velocity of

  A reversible power cycle receives enery qh from a hot

a reversible power cycle receives enery qh from a hot reservoir at th and rejects enerfy qc by heat transfer to a cold

  Explain feasibility

Determining Feasibility, At steady state, a new power cycle is claimed by its inventor to develop 6 horsepower for a heat addition rate of 400 Btu/min

  Find the change in diameter of a cylinder

how to find the change in diameter of a cylinder of 225mm length, 25mm diameter and a load of 180Km?

  To account for water losses in the cooling tower part of

the cooling water flow rate to the condensers of a big coal-fired power plant is 8460 kgs. the water enters the

  Determine the smallest horizontal force required to pull

determine the smallest horizontal force required to pull out wedge a. the crate has a weight of 200 and the coefficient

  Write a computer program that plots the contour lines of

write a computer program that plots the contour lines of sigma1 sigma2 on a 2d rectangular beam. sigma represents the

  The energy loss in the system is 25 times the velocity head

the pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 20 gallons per minute. the pressure

  A stainless steel bar 10 inch long and 38 inch in diameter

a stainless steel bar 10 inch long and 38 inch in diameter is loaded in tension and experiences an elastic stretch of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd