The heat transfer in the condenser the boiler and the

Assignment Help Mechanical Engineering
Reference no: EM13614313

Consider a steam power plant with reheat that operates on a modified Rankine cycle. Steam enters the high-pressure turbine at a pressure of 8 MPa and a temperature of 450 °C (State 1). The steam is expanded in the high-pressure turbine to a pressure of 1.6 MPa (State 2) and is then reheated to a temperature of 400 °C before entering the low-pressure turbine (State 3). The steam is expanded in the low-pressure turbine to a pressure of 4 kPa (State 4). Both turbines and the pump are adiabatic and internally reversible. The heat transfer in the condenser, the boiler, and the reheater take place at constant pressure. The water leaves the condenser as saturated liquid.

(a) Complete the table below.

(b) Determine the net specific work output of the cycle, in kJ/kg.

(c) Calculate the specific heat transfer into the cycle, in kJ/kg.

(d) Find the thermal efficiency of the cycle.

(e) Sketch the cycle on a T-s diagram. Label all points and processes.

Reference no: EM13614313

Questions Cloud

Determine the limits of the depth of field in the : a camera lens with a focal length of 50mm and aperture of f1.4 is used to image a scene. the photographer focuses the
Determine heat transfer required in the reheat unit kjkg if : consider a gas turbine with turbine staging and reheating. it operates under the following conditions.inlet air at 285
On january 2 todd company acquired 40 of the outstanding : on january 2 todd company acquired 40 of the outstanding stockof mcguire company for 205000. for the year
If this ice were to fall into the sea due to melting : the west antarctic ice sheets some 0.83 million km2 and only 6 of the total antarctic ice surface have an average
The heat transfer in the condenser the boiler and the : consider a steam power plant with reheat that operates on a modified rankine cycle. steam enters the high-pressure
Compute the static budget variances and the : the systems consulting department of johnson swimwear designsdata collecting encoding and reporting systems to fit the
The plane arrives in 200 h what were the a magnitude in kmh : a light plane attains an airspeed of 550 kmh. the pilot sets out for a destination 760 km due north but discovers that
On february 12 6000 shares of lucas company are acquired at : on february 12 6000 shares of lucas company are acquired at aprice of 22 per share plus a 240 brokerage fee. on april22
An other frame moves with a speed of 085 relative to the : an other frame moves with a speed of 0.85 relative to the home frame. an object at rest in the home frame has a length

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd