The heat is measured in either joules or calories

Assignment Help Civil Engineering
Reference no: EM13874297

When 2.5000g of NaOH were dissolved in 49.0g water in a calorimeter at 24.0 degrees C, the temperature of the solution went up to 37.1 degree C. eq.1. (q=(specific heat)x(mass in g)x(temperature change) q=(shxmx delta t) where delta t= (t final-t initial). the heat is measured in either joules or calories. (1 calorie=4.184 J).

a) calculate the mass of the solution (NaOH+H2O)

b) calculate q solution for the entire reaction (NaOH+H2O) as it occurred in the calorimeter using Eq.1. show calculations and watch sig figs.

c) calculate q reaction for the entire reaction (NaOH+H2O) as it occurred in the calorimeter using Eq.1. show calculation and watch sig figs.

d) Find q reaction (using part c) for the dissolving of 1.00g NaOH in water. (eq 4.(q reaction=-q aqueous solution= delta H reaction))

e) find delta H reaction (using part d) for the dissolving of 1.00 mole NaOH in water.

 

 

Reference no: EM13874297

Questions Cloud

Chemical transformation releases : As fresh poured concrete hardens, the chemical transformation releases energy at a rate of 2 W/kg. Assume the center of a poured layer does not have any heat loss and that it has an average heat capacity of 0.9 kJ/kg K. Find the temperature rise d..
Develop program that display information about family member : Develop a program that displays information about a family member or friend. This program should print out information about what you like best about him or her.
A sealed bottle of ''hard lemonade : A sealed bottle of 'hard lemonade' (lemonade with alcohol in it) is in a liquid-vapour equilibriumstate at 298.15 K. The liquid phase contains 250 mL of 5.40% alcohol (v/v) (meaning that for every100 mL of solution, 5.4 mL is pure ethanol) The number..
Distinguish between inflation risk and inflation as tax : Distinguish between inflation risk and inflation as tax
The heat is measured in either joules or calories : When 2.5000g of NaOH were dissolved in 49.0g water in a calorimeter at 24.0 degrees C, the temperature of the solution went up to 37.1 degree C. eq.1. (q=(specific heat)x(mass in g)x(temperature change) q=(shxmx delta t) where delta t= (t final-t ini..
Develop a java application for the local library : Develop a Java application for the local library as part of an upgrade initiative. As in all libraries, this is a place where one can check out books.
Find the number and name of each customer : Find the number and name of each customer that did not place an order on October 21, 2007
Klote company declared bankruptcy : Situation During 2010, one of the customers of Klote Company declared bankruptcy.
Outline a performance management plan : Create a PowerPoint Presentation for senior executives that will outline a performance management plan for a performance gap within your organization.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the volume flow rate of water

Water with a static pressure of 1.96kN/M 2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M 2 . How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/se..

  What is the discharge from the pipe

Flow occur  throught a sand-filled pipe with a cross-sectional area of 60 cm^2. If K is 10^-3 cm/s and the gradient is 0.01, what is the discharge from the pipe ?

  Determine the minimum size of the pad footing 2 meters wide

A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing 2 metres wide for a steel column if a factor of safety of 2.0 is recommended

  Calculate the uniform flow depth in the channel at flow rate

Water flows i a 8-m-wide rectangular channel that has longitudinal slope of .0001. The channel has an equivalent sand roughness of 2mm. Calculate the uniform flow depth in the channel when the flow rate is 15m^3/s. Use the Darcey-Weisbach equation..

  Calculate the steady state p concentration in the lake

A) calculate the steady state P concentration in the lake B)Creek A has been identified as the easiest to control. What would the P concentration have to be reduced to in Creek A, in order to reduce the concentration in the lake below 0.025 mg/l

  Determine the elevation vs. surface area relationship

Determine the elevation vs. surface area relationship for the vault and use this information to calculate and graph the elevation-storage relationship. Use the average end area method.

  Determine the work done and the heat transfer

Water, initially dry saturated vapour at 4 bar, lls a closed rigid con- tainer. The water is heated until its temperature is 400C. Determine the work done and the heat transfer.

  Determine the hydraulic conductivity of the sand in field

In the field, if the relative compaction is 90%, determine the hydraulic conductivity of the sand in the field compaction condition (given that k for the sand at the maximum dry density condition is .040 cm/sec and Gs = 2.65).

  Determine its changes in kinetic and potential energy

An automobile having a mass of 900 kg initially moves along a level highway at 100 km/hr relative to the highway. It then climbs a hill whose crest is 50m above the level highway and parks at a rest area located there

  Determine the x and y scalar components

The forces F1, F2, and F3, all of which act on point A of the bracket, arespecified in three different ways. Determine the x and y scalar components of each of the three forces.

  What horizontal force on each lower bar is necessary to keep

Two similar cylindrical polished bars weighing 5.00 N each lie next to one another in contact.A third similar bar is placed on the other two in the groove between them.Neglecting friction,what horizontal force on each lower bar is necessary to keep t..

  Determine the instantaneous center of rotation of the spool

Knowing that end B of the tape is pulled downward witha velocity of 300 mm/s and that at the instant of the total thickness of the tape on the spool is 20 mm, determine (a) the instantaneous center of rotation of the spool,

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd