The gap width is g mm and the inner cylinder radius is r mm

Assignment Help Mechanical Engineering
Reference no: EM13644507

A fluid has a viscosity of X N*s/m^2 and is placed in a concentric cylinder viscometer. The gap width is G mm and the inner cylinder radius is R mm. Determine the shear rate and the shear stress in the blood if the angular velocity of the outed cylinder is 60rpm.

Reference no: EM13644507

Questions Cloud

A window washer is standing on a scaffold supported by a : a window washer is standing on a scaffold supported by a vertical rope at each end. the scaffold weighs 200 n and is
The object is attached to the rope at a horizontal position : an object of mass m 6.64kg is attached to a rope of negligible mass that is strung between two tops of two vertical
Using the appropriate form of the heat equation derive an : consider a one-dimensional plane wall with constant properties and uniform internal generation qdot. the left face is
If an additional 50 mj of energy are supplied to the : a 1.2-kg 10-cm-diameter solid sphere is rotating about its diameter at 69 revmin.a what is its kinetic energy?b if an
The gap width is g mm and the inner cylinder radius is r mm : a fluid has a viscosity of x nsm2 and is placed in a concentric cylinder viscometer. the gap width is g mm and the
1 if the angle between the rope and the horizontal is 117 : an adventurous archaeologist crosses between two rock cliffs by slowly going hand-over-hand along a rope stretched
Given the initial volume is 10 ft3 and a system expands to : given the initial volume is 10 ft3 and a system expands to 20 ft3 and the system has an initial pressure of 14.7 psi
Calculate the span of a differential pressure transmitter : calculate the span of a differential pressure transmitter that is mounted 10 inches below the bottom instrument tap on
If b 25 t and the particle has a charge- to-mass ratio of : a charged particle is moving downward with an initial speed of 5 times 106 ms when it encounters a uniform magnetic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  An air compressor receives atmospheric air at t0 17degc

an air compressor receives atmospheric air at t0 17degc 100 kpa and compresses it up to 1400 kpa. the compressor has

  The collector transfers heat by natural convection to the

a flat plate solar collector 6ft by 12ft is mounted on the roof of a house. the outer surface of the collector is at

  The bell-crank mechanism consists of a bent rod and an

the bell-crank mechanism consists of a bent rod and an attached 5-kg weight. the rod has negligible weight and the mass

  During a test it is found that this represents 28 of the

a power station output is 500 megawatts. during a test it is found that this represents 28 of the energy put into the

  Determine the rotor diameter and the nozzle angle if the

an inward radial flow turbine is to develop 400 hp when supplied with air at 800c and 3 bar abs the exhaust total

  Determine for the modified cycle a the coefficient of

air enters the compressor of an ideal brayton refrigeration cycle at 120 kpa and 275 k. the compressor pressure ratio

  The wall of a cold storage consists of three layers- an

the wall of a cold storage consists of three layers- an outer layer of ordinary bricks 25 cm thick a middle layer of

  A what is the approximate ductility el of a brass alloy

a what is the approximate ductility el of a brass alloy that has a yield strength of 275 mpa? what is the tensile

  Determine a the minimum diameter of the inlet pipe in cm so

ammonia enters a control volume operating at steady state at p1 14 bar t1 28 oc with a mass flow rate of 0.5 kgs.

  Determine the following 1 the compressor work kjkg 2 the

an ideal cold air-standard brayton cycle engine operates with air entering the compressor at 27 c. the pressure ratio

  A rankine cycle steam plant operates between the pressures

a rankine cycle steam plant operates between the pressures of 15 mpa and 6 kpa. steam exiting the boiler is 550 degrees

  They mix without any heat transfer to produce an exit flow

two oxygen o2 flows are combined to a single flow. one flow is 1.5 m3s at 25degc and the other is 2.5 m3s at 250degc

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd