The force weight from a hanging sign attached at the outer

Assignment Help Mechanical Engineering
Reference no: EM13634677

There is a bracket with a long rail on the top that is connected to a vertical pole with a pin. There is another bracket also attached to this 6ft rail in its middle with another pin. It is made up of two pieces each one 3ft in length and connected together with another pin. That part is also connected to the pole 3ft below the top rail. There is a cable which runs diagonal from the two piece bracket and the top rail where it is attached to the pole. Using virtual work, what is an expression of the relationship between the tension in the cable (Q) and the force (weight) from a hanging sign attached at the outer tip of the top rail (P)? What will the tension be if a 50lb sign is hung at the tip of the bracket?

Reference no: EM13634677

Questions Cloud

Write down the balanced chemical equation for one lbmol of : ethane gas at 140 f is burned in a steady-flow process with theoretical air at 40 f in such a way that the products are
In a test of weight loss programs 198 subjects were divided : in a test of weight loss programs 198 subjects were divided such that 33 subjects followed each of 6 diets. each was
The activation energy for the diffusion of atomic species : the activation energy for the diffusion of atomic species a inmetal b is 125 kjmol. calculate the diffusion coefficient
A how much farther west does the blue boat travel compared : two racing boats set out from the same dock and speed away at the same constant speed of 86.0 kmh for half an hour
The force weight from a hanging sign attached at the outer : there is a bracket with a long rail on the top that is connected to a vertical pole with a pin. there is another
Three particles are fixed on an x axis particle 1 of : three particles are fixed on an x axis. particle 1 of charge q1 is at x -a and particle 2 of charge q2 is at x a. if
Calcium carbonate the major component of limestone : a. the carbon dioxide of the atmosphere being a nonmetallicoxide and acid anhydride has a low solubility in rainwater
A metal bar 122 mm long and having a square cross section : a metal bar 122 mm long and having a square cross section with an edge length of 17 mm is pulled in tension with a load
A longitudinal standing wave is established in a tube open : a longitudinal standing wave is established in a tube open at one end only. in air the fundamental frequency is 110 hz.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd