The exit conditions are 10 kpa with a quality of 9

Assignment Help Mechanical Engineering
Reference no: EM13644162

Steam flows steadily through an adiabatic turbine. The inlet conditions ar 10 MPa, 450 degrees C, 80 m/s and inlet area of .004 m^2. The exit conditions are 10 kPA with a quality of .9. Determine the power output of the turbine. Determine the adiabatic efficiency of the turbine.

Reference no: EM13644162

Questions Cloud

In one case pressure is raised at tconstant then t is : water is heated from 100kpa 20 deg c to 1000kpa 200 deg c. in one case pressure is raised at tconstant then t is raised
What is the probability that a randomly selected student : suppose that the amounts that students at a college spend on textbooks this semester have a normal curve with mean ? mu
What is the ionization energy of rubidium atoms in : the ionization energy of an atom can be measured by photoelectron spectroscopy in which light of wavelength is directed
Assume steady state operation and kinetic and potential : water is the working fluid in as ideal rankine cycle. saturated vapor enters the turbine at 16 mpa state 1 and the
The exit conditions are 10 kpa with a quality of 9 : steam flows steadily through an adiabatic turbine. the inlet conditions ar 10 mpa 450 degrees c 80 ms and inlet area of
A 1000 ml portion of hcl sol was diluted to 5000 ml if 500 : a 10.00 ml portion of hcl sol was diluted to 50.00 ml. if 5.00 ml of this solution required 41.00 ml of 0.2550 m sodium
It enters the regenerator with an effectiveness of 075 it : a regenerative brayton cycle has two step isentropic compression with cooling. air enters the first compression at 300
Steam from a boiling teapot 100 degc hits a persons hand : steam from a boiling teapot 100 degc hits a persons hand and causes a burn. assuming 1 g of water vapor condenses to
Determine how much force will be required to stretch them : a set of steel reinforcing rods is to be stretched axially in tension to create a tensile stress of 30ksi prior to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the rates of exergy destruction in the compressor

air enters the compressor of a cold air-standard brayton cycle at 100 kpa 300 k with a mass flow rate of 6 kgs. the

  If the tension is maintained at the value determined in

the crate has a mass of 150kg and the coefficients of friction between it and the sloping dock are mus 0.5 and muk

  The 2-kg ball rests between the 45 degree grooves a and b

the 2-kg ball rests between the 45 degree grooves a and b of the 10 degree inlcine and against a vertical wall at c. if

  Briefly explain a why there may be significant scatter in

briefly explain a why there may be significant scatter in the fracture strength for some given ceramic material and b

  Why is the carnot cycle not suitable as an ideal cycle

why is the carnot cycle not suitable as an ideal cycle for all the power producing devices ?

  Fnd the ratio of the earths translational ke to its daily

find the ratio of the earths translational k.e to its daily rotational k.e. assume the orbit about the sun is circular

  What is the rpm of the fan three seconds after it is turned

the angular acceleration of a fan blade once the fan is turned on is found to be 15 t12 for the first five seconds. a

  The average surface temperature of the plates is 10 degree

saturated ammonia vapor at 30 degree in celcius is passed over 30 vertical flat plates each of which is 10 cm high and

  The steam line leading to the turbine inle

The steam line leading to the turbine inle

  Using a unifrom mesh size deltax deltay determine the

consider steady two dimensional heat transfer in a square cross section 3cm x 3cm with the prescribed temperatures at

  How many lbf does it take for a 40 x 103 lbm car to achieve

how many lbf does it take for a 4.0 x 103 lbm car to achieve 0 to 60 mph in 10. seconds? use fma where a is

  The diameter of the rod is 25mm internal diameter and its

a long rod is exposed at air at 298oc. it is heated at one end. a steady state condition the temp at 2points along the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd