The engine is used to drive an electrical generator that is

Assignment Help Mechanical Engineering
Reference no: EM13622453

1. An aluminum casting that weighs 10 pounds sits on a steel surface. How much force will be necessary to get it to start sliding? The static coefficient of friction (mu) for aluminum on steel is 0.61.

2. A robot arm must be able to extend 87 cm in 3 s. while carrying a load of 6 kg. How much force is required in Newtons?

3. A torque of 15 N-m is applied to a rotating part. The moment of inertia is 0.078 kg-m2. How much time (in seconds) will it take to rotate the part 90 degrees?

4. A small gasoline engine can put out 12,000 N-m/min of mechanical power. The engine is used to drive an electrical generator that is 60 percent efficient. 1 N-m = 2.78 X 10-4 W-h. Find the output of the generator in Watts.

5. A proportional controller for a rotating antenna has a gain of Kp of 5 in-oz/deg. The antenna was initially pointing south, but was then commanded to point southeast. Find the torque applied to the antenna in in-oz, when the antenna is within 5 degrees of southeast.

6.The steering wheel has backlash. This means there is a delay between the time the wheel is turned, and the time the car responds. The driver tends to overturn, which leads to instability and lack of control of the car. In the presence of backlash, discuss what steps the operator can take to reduce the instability.

Reference no: EM13622453

Questions Cloud

An ac generator consists of 6 turns of wire each turn has : an ac generator consists of 6 turns of wire. each turn has an area of 0.040m2. the loop rotates in a uniform field
If the bead is released from rest halfway between the two : consider a horizontal parallel plate capactor where the size of the plates is much larger than the spacing between the
If their velocities measured relative to the cart are 3fts : the 80-lb boy and 60-lb girl walk towards each other wit a constant speed on the 300-lb cart. if their velocities
A student survey was done to study the relationship between : a student survey was done to study the relationship between where students live dormitory apartment house co-op or
The engine is used to drive an electrical generator that is : 1. an aluminum casting that weighs 10 pounds sits on a steel surface. how much force will be necessary to get it to
Two convex lenses with focal lengths f1 60cm and f2 80cm : two convex lenses with focal lengths f1 6.0cm and f2 8.0cm are located 24.4cm apart. an object is located 13cm in
An ac generator consists of 6 turns of wire each turn has : an ac generator consists of 6 turns of wire. each turn has an area of 0.040m2. the loop rotates in a uniform field
Knowing that the coefficient of static friction between the : a truck is traveling on a level road at a speed of 60 mih when its brakes are applied to slow it down to 20 mih. an
The plates of a spherical capacitor have radii 37 cm and 4 : the plates of a spherical capacitor have radii 3.7 cm and 4 cm with a vacuum in between them.a. find the surface area

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the power needed to drive the pump if the pump

a feed water pump operates with a flow rate of 350 kgs. the water enters at 420 k. the inlet pressure is 0.7 mpa and

  A six-station automatic assembly line has an ideal cycle

a six-station automatic assembly line has an ideal cycle time of 12 sec. downtime occurs for two reasons. first

  Determine the initial state and the end state of the gas

an un-stretched spring initially is attached to a horizontal piston round shape. heat is added to the gas until the

  Examine the rate of heat generation

Need help with determining the rate of heat generation required at the welding source to accomplish a weld. A fillet weld is used to join two medium carbon steel plates each having a thickness of 5.0mm.

  Calculate the specific volume for carbon dioxide gas at 450

calculate the specific volume for carbon dioxide gas at 450 k and 4000 kpa using a ideal gas equation b compressibility

  The bottom of the distillation column is essentially

an alcohol solution contains 6 by mass ethanol. this solution is fed to a distillation column at a rate of 1000 kgh.

  Find humidity ratio and relative humidity

A mixture of dry air and water vapor is at a temperature of 21C under a pressure of 101.3 kPa.The dew point temperature is 15C.(Ps= saturation pressure at 15C=1.7044 kPa;Pd=saturation pressure at 21C=2.4861 kPa) find humidity ratio and relative hu..

  Problem 110degc water is flowing in a 10-mm diameter smooth

problem 110degc water is flowing in a 10-mm diameter smooth tube. the mass flow rate of the water is 0.15 kgs. the

  Finally compressed at the constant pressure to the initial

a piston-cylinder device contains 0.15kg of air initially at 2mpa and 350oc. the air is first expanded isothermally to

  A circular coil having 19 turns and a radius of r 176cm

a circular coil having 19 turns and a radius of r 17.6cm carries a current of 3.80a. it is placed in a uniform

  Calculate the overall efficiency the heat rate mw and the

calculate the overall efficiency the heat rate mw and the total fuel rate kgs of a combined-cycle power plant 1 if no

  Calculate the output speed of the driven sheave

A 5v belt drive system operates an input speed of 1250 RPM at the small sheave. The driving sheave has a pitch diameter of 6.000 in, and the driven sheave has a pitch diameter of 19.000 in. If an optimum center distance of 47 in is specified.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd