The electricity consumption

Assignment Help Mechanical Engineering
Reference no: EM13706605

The electricity consumption in the USA in 2009 was about 44% of the total energy consumption. Of that about 20% was produced by Nuclear Power Plants. Currently there are 104 Nuclear Power Plants operating in the country. What is the average capacity of each of these plants in megawatts. If each reactor unit in the power plant has a capacity of 1000MW, how many such units, on an average, in each Plant?

Reference no: EM13706605

Questions Cloud

Determine the final pressure and temperature in the tank : A closed rigid tank of volume 3m^3 contains a two-phase liquid-vapor mixture of H2O at 110C with a quality of 34.5%. The tank then receives energy by heat transfer until the water becomes a saturated vapor. Determine the final pressure and temperatur..
What is its temperature and quality : R134a rests in a compressed fluid can at 120psia, and a specific volume of 0.38ft3/lbm. What is its temperature and quality? Half of the mass is now vented off to the atmosphere. The can is allowed to exchange heat with the surroundings at 100°F unt..
Idealized reservoir contains an ideal gas at a pressure : An idealized reservoir contains an ideal gas at a pressure of 4410 psia and a temperature of 91degrees C. Under these conditions the volume of this gas in the reservoir is 10^9 ft^3. What would be the volume of this gas at standard temperature and co..
Double the pressure of the gas inside the cylinder : A vertical piston-cylinder device contains a gas at a pressure of 100 kPa. The piston has a mass of 5 kg and a diameter of 12 cm. Pressure of the gas is to be increased by placing some weights on the piston. Determine the local atmospheric pressure a..
The electricity consumption : The electricity consumption in the USA in 2009 was about 44% of the total energy consumption. Of that about 20% was produced by Nuclear Power Plants. Currently there are 104 Nuclear Power Plants operating in the country. What is the average capacity ..
What is the density of the unknown liquid : Two pipes containing air are connected with two manometers, as shown in the figure. One manometer contains glycerine, and the difference in liquid levels is 10 cm. The other manometer contains an unknown fluid, and it shows a difference in liquid lev..
Rectangular gate is used as a retaining wall : A rectangular gate is used as a retaining wall for seawater as shown in the figure. The gate is hinge at point O 1 m from the bottom. Determine the depth of seawater required for the resultant force to be located at the hinge. The gate width into the..
Advanced engineering thermodynamics by began : Decide one by one the exact location of the points that appear in the two dimensional plot of fig 2.8. How many different paths can the system follow from state a to state b (chapter 2, advanced engineering thermodynamics by began)
How much energy is required to accelerate : How much energy (kJ) is required to accelerate a 1500 kg passenger vehicle from rest to highway speed (110 km/hr)? If it takes fifteen seconds to accelerate the vehicle, what is the average power (kW)?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd