User Account

All Pages

The displacement vectors 460 cm at 150deg and 230 cm at

Assignment Help Mechanical Engineering
Reference no: EM13643660

The displacement vectors 46.0 cm at 15.0° and 23.0 cm at 56.0° both start from the origin and form two sides of a parallelogram. Both angles are measured counterclockwise from the x axis.

(a) Find the area of the parallelogram.

(b) Find the length of its longer diagonal.

 

Reference no: EM13643660

Questions Cloud

A uniform solid sphere of radius r 0480 m and mass m 170 : a uniform solid sphere of radius r 0.480 m and mass m 17.0 kg turns counterclockwise about a vertical axis through
Suppose that the amount of time between consecutive surges : suppose that the amount of time between consecutive surges in an electricity network has an exponential distribution
The energy from radiation can be used to cause the rupture : the energy from radiation can be used to cause the rupture of chemical bonds. a minimum energy of 941 is required to
In a physics laboratory experiment a coil with 180 turns : in a physics laboratory experiment a coil with 180 turns enclosing an area of 13.5 cm2 is rotated during the time
The displacement vectors 460 cm at 150deg and 230 cm at : the displacement vectors 46.0 cm at 15.0deg and 23.0 cm at 56.0deg both start from the origin and form two sides of a
A 600-o resistor is connected in parallel with a 1200-o : a 60.0-o resistor is connected in parallel with a 120.0-o resistor. this parallel group is connected in series with a
An aerated lagoon with a liquid volume of 3000 m3 is : an aerated lagoon with a liquid volume of 3000 m3 is designed to accommodate an inlet flow rate of 105 lmin. bod
The owner of a small convenience store is trying to decide : the owner of a small convenience store is trying to decide whether to discontinue selling magazines. he suspects that
Find a the angle between the direction of motion of the : in a game of pool the cue ball strikes another ball of the same mass and initially at rest. after the collision the cue

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Express the finite difference formulation of the boundary

consider steady heat conduction in a plane wall whose left surface node 0 is maintained at 40 degrees c while the right

  A 012 ounce bullet hits at 2000 fts a suspended 10-lb

a 0.12 ounce bullet hits at 2000 fts a suspended 10-lb block of wood and becomes embedded in it. the angle alpha

  Show the cycle on a t-s diagram with respect to the

consider a 210mw steam power plant that operates on a simple rankine cycle. steam enters the turbine at 10mpa and 500oc

  A vehicle is powered by motors that have a maximum speed of

a vehicle is powered by motors that have a maximum speed of 5000 rpm. each motor is coupled to the wheel using a gear

  If the initial flow rate through the pipe is 12 ls

two water reservoirs a and b are connected to each other through a 40 m long 2 cm cast iron pipe with a sharp-edged

  Determine the mass flow rate of air going through the

1 a gas turbine power plant produces a net power output of 100 mw with an overall thermal efficency of 35a if the

  Tensile stress and compressive stress

How the tensile stress and compressive stress result in the moment about neutral axis when the beam fails

  A 6 nominal pipe size schedule 40 steel pipe has a

a 6 nominal pipe size schedule 40 steel pipe has a chamfered entrance and 300 ft. long. the velocity is 20 ft per sec.

  A standard deviation of 003 mm if 250 shaft and hubs are

a hub and shaft are said to meet satisfactory fit if the clearance between the two is between 0.03 and 0.18 mm. the

  If a number of the hot air balloons started from the same

a hot air balloon travels with the wind. the wind velocity is v6i 10j ms for the first hour and then it is 10i 5j ms

  However he does not record the direction of the flow show

a line worker takes the following measurements in a constant diameter pipe pa 200kpa za 56m pb 100kpa zb 68m.

  It is observed that snow lies stably on roofs with a slope

question it is observed that snow lies stably on roofs with a slope of less than 24deg but that it slides off roofs

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd