The discharge temperature is 400 c a heat loss of 10 kw is

Assignment Help Mechanical Engineering
Reference no: EM13611660

A steam compressor is used to increase the pressure of saturated water vapor at 1000 kpa to 1500 kpa. The flow rate is 45 kg/h, and the discharge temperature is 400 C. A heat loss of 1.0 kw is measured. Neglect changes in kinetic and potential energy. Determine the power input (kw) to the compressor.

Reference no: EM13611660

Questions Cloud

Suppose the thickness of the membrance is doubled but the : a typical cell membrane is 7.1 nm thick and has an electrical resistivity of 1.3 x 107 m. if the potential difference
Cucumber company concluded at the beginning of 2013 that : cucumber company concluded at the beginning of 2013 that the companys ownership interest in pickelco had decreased to
What is the probability that the number of uninsured : let x be the number of uninsured drivers in a random sample of 100 drivers.if 33 of all licensed drivers do not have
The 1800000 note receivable is dated may 1 2006 : transactions during 2007 and otherinformation relating to connecticuts long-term receivables were asfollows.the 1800000
The discharge temperature is 400 c a heat loss of 10 kw is : a steam compressor is used to increase the pressure of saturated water vapor at 1000 kpa to 1500 kpa. the flow rate is
If in reality 54 of the residents oppose building the : a community vote is being held to see if a factory will be built in the community. a survey firm randomly surveyed 180
An iron wire has a cross-sectional area of 101 x 10-5 m2 : an iron wire has a cross-sectional area of 1.01 x 10-5 m2. carry out steps a through e to compute the drift speed of
Shown below are rental and leasing revenue figures for : shown below are rental and leasing revenue figures for office machinery and equipment in the united states over a
On september 30 2013 sternberg company sold office : on september 30 2013 sternberg company sold office equiptment for 12000. the equiptment was purchased on march 31 2010

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The uniform work platform which has a mass per unit length

the uniform work platform which has a mass per unit length of 21 kgm is simply supported by cross rods a and b. the

  Determine expressions for attractive and repulsive energies

determine the expressions for attractive and repulsive energies, EA and ER as a functions of r where r is in nm and E is in eV.

  Determine the resultant force applied

A short post AB has a commercially manufactured eyebolt screwed into its end. Three cables attahced to the eyebolt apply forces shown.

  Estimate the ship speed

The kite cable makes an angle of 25 degrees with the horizontal. The velocity of the wind is 30 miles/hour. Neglect ship wave drag.

  Water flows as two free jets from the tee attached to the

water flows as two free jets from the tee attached to the pipe shown below. thenbspexit speed is 15 ms. if viscous

  In the rectangle in the drawing a charge is to be placed at

in the rectangle in the drawing a charge is to be placed at the empty corner to make the net force on the charge at

  Heat is transferred to the steam until the temperature

A piston-cylinder device has a volume of 0.1 cubic meters and contains 0.5kg of steam at 0.4 MPa. Heat is transferred to the steam until the temperature is 300 degrees Celsius

  Two slender rods of negligible weight are pin-connected at

two slender rods of negligible weight are pin-connected at a and attached to the 18-lb block b and the 80-lb block c as

  A solid shaft l 19 m long is supported between two bearings

a solid shaft l 1.9 m long is supported between two bearings. the shaft rotates at 250 rpm. a 20 degree involute gear

  The drag force on the ball is fd 0002v2 where fd is in

a spring loaded device imparts an initial vertical velocity of 50 ms to a 0.15 kg ball. the drag force on the ball is

  Evaluate the effect of the water spray on efficiency

Evaluate the effect of the water spray on efficiency (net work out divided by heat input) and net power out per kg/s of dry air coming into the turbine.

  Calculate the rate of change of heat with the cylinder

how do i calculate the rate of change of heat with the cylinder, and the vertical temperature distribution along the cylinder's wall.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd