User Account

All Pages

The cross sectional area is 05 cm2 and is of length 50 cm

Assignment Help Mechanical Engineering
Reference no: EM13638910

A cylindrical rod of an unknown material is subject to a force of 20000N. The cross sectional area is 0.5 cm2 and is of length 50 cm. If the Young's Modulus was observed to be 500 GPa, calculate the new area if the Poisson's ratio is 0.3.?

Reference no: EM13638910

Questions Cloud

What are the corresponding values of tensile strength yield : a cylindrical steel rod 0.5 in diameter is cold worked to reduce the area. the new diameters in 3 cases are 0.43in
If the angle of slip direction is 430 and the normal to the : the critical shear stress for a crystal material is 3250 psi. if the angle of slip direction is 430 and the normal to
Find the mean median and mode for the set of scores in the : find the mean median and mode for the set of scores in the following frequency distribution table. round to 1 decimal
Assuming the volume of the stomach to be 10l what will be : 1.a 0.187g sample of a co3-2 antacid isdissolved with 25.0 of 0.0984 m hcl. the hydrochloric acidthat is not
The cross sectional area is 05 cm2 and is of length 50 cm : a cylindrical rod of an unknown material is subject to a force of 20000n. the cross sectional area is 0.5 cm2 and is of
In a binomial experiment the probability of success is 006 : in a binomial experiment the probability of success is 0.06. what is the probability of at most two successes in seven
A sports photographer has a 150 mm focal length lens on his : a sports photographer has a 150 mm focal length lens on his camera.the photographer wants to photograph a sprinter
Kasandra associates provides executive coaching services to : kasandra associates provides executive coaching services to fortune 100 senior executives. her team charges 190 per
The mean value of the coefficient of friction is 025 and : a plate clutch has a single pair of mating friction surfaces 300 mm od by 225 id. the mean value of the coefficient of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the entropy change of the water in kjkg middotk

two kilograms of saturated water vapor at 600 kpa are contained in a piston-cylinder device. the water expands

  Find the work done if the pressure between the initial and

a system has an initial volume of 10 ft3 and expands to a final volume of 20 ft3. the initial pressure is 15 psia. find

  Calculate athe mass of the air that has entered the tank

a 1-m3 rigid tank initially contains air at 150 kpa 300 k. the tank is connected through a valve to a supply line at

  Vector s makes angle of 45 degree with x-axis and 60

vector r makes angle of 30 degree with x- axis and 70 degree with y-axisand it is in the positive octant. vector s

  Calculate the specific weight in lbfft3 on earth and on the

the density of mercury is given as 26.3 slugft3. calculate the specific gravity and the specific volume in m3kg of the

  Ethane gas is burned in a steady-flow process with 30

ethane gas is burned in a steady-flow process with 30 excess air both of which enter separately at 25 0 c and 1 atm.

  Determine the temperature of the air entering the combustor

a stationary gas turbine engine is used for generating electricity during times of peak demand. dry air at tamb 20oc

  If the peak of the trajectiry is at 8 km from the launch

a projectile is launched at a with a spped u and 45 degree launch angle. if the peak of the trajectiry is at 8 km from

  A stream of refrigerant-134a at 1 mpa and 12 c is mixed

a stream of refrigerant-134a at 1 mpa and 12 c is mixed with another stream at 1 mpa and 60 c. if the mass flow rate of

  Calculate the bulk density of a rock which has 20 porosity

calculate the bulk density of a rock which has 20 porosity. the bulk mineralogy of the rock is 80 quartz 15 calcite and

  A series of parcels is carried on a belt which goes over a

a series of parcels is carried on a belt which goes over a pulley with 600 mm diameter. if the belt starts from rest

  A thermocouple is located 1 m from the leading edge of a

a thermocouple is located 1 m from the leading edge of a flat plate along which water flows at 1 ms. the distance

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd