User Account

All Pages

The convection heat transfer coefficient in the furnace is

Assignment Help Mechanical Engineering
Reference no: EM13631015

In an annealing process, a stainless steel plate (50 mm thick) will be heated to at least 600°C from an initial temperature of 230 C in a furnace that is at 1000°C. The convection heat transfer coefficient in the furnace is uniform and 215 W/m^2-K. Determine the time it takes to heat the plate to the target temperature of 600°C.

Reference no: EM13631015

Questions Cloud

Air at 1 atm and 15 c blows parallel to the 8m side at a : a rectangular solar thermal collector sits on the roof of a house only one side is exposed to air and solar radiation
The water will be heated by passing it through a 2m long : 10 degree c water is flowing in a 10mm internal diameter smooth tube. the mass flow rate of the water is 0.07 kgs. the
When a seacond block with the same dimension but 3 times : a block is made of an unknown material. when placed in water the block floats and 4 m3 of the block is observed to be
The water will be cooled to 20 degrees c by passing it : 50 degree c water is flowing in a 10mm diameter smooth tube. the mass flow rate of the water is 0.08 kgs. the water
The convection heat transfer coefficient in the furnace is : in an annealing process a stainless steel plate 50 mm thick will be heated to at least 600degc from an initial
The boat moves 25cm relative to the water as a result of : you and a friend are in a small boat on table rock lake. when the boat is not moving with respect to the water you and
What is the maximum thermal conductivity of the insulation : we need to select an insulation material to reduce the heat loss from a tubing 0.5 cm in outer diameter. the outside of
Were you exceeding the 40 mph 1787 ms speed limit before : you are driving a 1200kg mini cooper east on central. you look down to read a text message from your mom. when you look
A hot-water stream at 80 degrees c enters a mixing chamber : a hot-water stream at 80 degrees c enters a mixing chamber with a mass flow rate of 0.5 kgs where it is mixed with a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At the beginning of the compression process of an

at the beginning of the compression process of an air-standard otto cycle p1 14.7 lbin2 and t1 530degr. the maximum

  Question 1 a force of 750 n acts on point a in the x

question 1 a force of 750 n acts on point a in the x direction where the cables ab ac and ad are joined as shown in

  Knowing that a downward force of magnitude 120 n is applied

the masses of blocks a b c and d are 9 kg 9 kg 6 kg and 7 kg respectively. knowing that a downward force of magnitude

  Computing the second moment of area

It is necessary to design a square-section composite bar that will withstand an applied load without deflecting more than a specified amount.The design specification for the bar, including its dimensions and loading criteria, is given below.

  A plane wall 15 cm thick has a thermal conductivity given

a plane wall 15 cm thick has a thermal conductivity given by the relation k 2.0 0.0005t wmk. where t is in kelvin.

  Assuming the wheels do not slip on the ground determine the

the jeep has a weight of 2510lb and an engine which transmits a power of 100 hp to all the wheels. assuming the wheels

  Theory and practice of the product

Derive at least four concept designs to satisfy the given specification. Use short written descriptions and simple sketches to illustrate your ideas

  A sphere is fired downwards into a medium with an initial

a sphere is fired downwards into a medium with an initial speed of 27 ms. if it experiences a deceleration of a -6t

  Using cv constant theory an using thermal properties at

in a diesel cycle the cutoff ratio is two and the compression ratio is eighteen. at state 1 the air is 14.7 psia and

  Calculate the percent energy distribution in a steam

calculate the percent energy distribution in a steam generator that goes into steam losses to flue gases refuse and

  A tank open to the atmosphere initially contains 2 lb of

a tank open to the atmosphere initially contains 2 lb of liquid water initially at 80degf and 0.4 lb of ice initially

  Determine the magnitude of the particles displacement from

a particle is traveling with a velocity of v 3sqrtte-0.2ti 4e-0.8t2j ms where t is in seconds. determine the magnitude

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd