The compressed liquid water enters the desuperheater at

Assignment Help Mechanical Engineering
Reference no: EM13627567

A desuperheater is a steady-flow, adiabatic mixing process that mixes superheated water vapor with colder liquid water to produce a stream of saturated water vapor. The superheated water vapor enters the desuperheater at 5MPa, 400 degrees cenitgrade at a mass flow rate of 0.5kg/s. The compressed liquid water enters the desuperheater at 5MPa, 40 degrees centigrade. Water exits the desuperheater as 4.5Mpa saturated vapor. Find the required mass flow rate of the compressed liquid.

Reference no: EM13627567

Questions Cloud

Find a mathematical expression for each of the following : imagine a thin cylinder of initial internal diameter do initial wall thickness to and initial fixed length fixed by two
What would happen if you place a 1m by 2 m sheet of : what would happen if you place a 1m by 2 m sheet of aluminum extruded and place it on the roof of your car driving at
Light of wavelength 455 nm is incident on a narrow slit the : light of wavelength 455 nm is incident on a narrow slit. the diffraction pattern is viewed on a screen 3.11 m from the
Using a 001 significance level test the inspectors claim : the acme bacon company distributes bacon in packages labelled 500 grams. an inspector randomly selects 49 of these
The compressed liquid water enters the desuperheater at : a desuperheater is a steady-flow adiabatic mixing process that mixes superheated water vapor with colder liquid water
A ships hull is 150m long as has a wetted area of 5000 m2 : a ships hull is 150m long as has a wetted area of 5000 m2. when it is encrusted with barnacles it requires 7000 hp to
In a double-slit interference experiment the wavelength is : in a double-slit interference experiment the wavelength is 467 nm the slit separation is 0.110 mm and the screen is
The heat transfer from the compressor to the surroundings : refrigerant 134a enters a compressor at 200kpa 100 quality and exits at 1mpa 60 degrees centigrade. the speed of the
The centerboard of a sailboat is 25m long and has a chord : the centerboard of a sailboat is 2.5m long and has a chord of 1m. approximate the centerboard as a flat plate in water

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the rods angular velocity

A rigid bar of mass m and length L is released from rest in the horizontal position. What is the rod's angular velocity when it has rotated through 90°?

  Determine the maximum theoretical power that could be

steam exits a turbine with a mass flow rate of 2x105 kgh at a pressure of 0.008 mpa quality of 94 and velocity of 70

  The retracting load on a 2 in diameter hydraulic cylinder

the retracting load on a 2 in diameter hydraulic cylinder increases from 10000 lbto 15000 lb. du to the compressibility

  The player pulls his hand back during the impact at an

a baseball player catching a ball can soften the impact by pulling his hand back. assuming that a 5-oz ball reaches his

  If the pipe diameter is 30 cm compare the head loss

a 6-km cast-iron new pipeline conveys 320 lsec of water at 30 degrees celsius. if the pipe diameter is 30 cm compare

  Determine an expression for the steadystate temperature tb

a cylindrical metal rod length 2l radius r thermal conductivity k is embedded in a well-insulated wall such that half

  If the coefficient of performance of the heat pump is 9 and

a heat engine with a thermal efficiency of 40 receives heat from a reservoir at a temperature of 300of and rejects heat

  This allows the free-stream velocity to remain constant at

a wind tunnel has a 1-m2 6-m-long test section in which air at standard sea-level conditions moves at 70 ms. it is

  If the cylinder is to be protected against excessive

a hydrogen tank 25 cm in diameter and 80 cm in height is charged to 150 atmospheres at room temperature 25 c. a

  A machinist is making engine parts with axle diameter of 07

a machinist is making engine parts with axle diameter of 0.7 inch. a random sample of 15 parts shows mean diameter

  Explain mechanical vibrations in a steel beam

Twenty-five samples of steel beam were chosen and tested for Young's Modulus. Eight had a modulus of E = 30 x 10^6 psi. Two had a modulus of E = 29 x 10^6 psi. Fifteen had a modulus of E = 30. x 1-^6 psi.

  A normal shock wave exists in mach 2 stream of air having

a normal shock wave exists in mach 2 stream of air having temperature and pressure of 45degf and 30 psia respectively.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd