User Account

All Pages

The coeficient of discharge is 097 calculate the rate of

Assignment Help Mechanical Engineering
Reference no: EM13344846

A ventuti meter installed in a horizantal water main of diameter 150mm has athroat diameter of75mm. The coeficient of discharge is 0.97. Calculate the rate of flow in the main in m3/hr if the diffrence in levels piezometers connected to the throat and inlet tapping is 25.4cm.

Reference no: EM13344846

Questions Cloud

Calculate the heat released when 195 l of cl2g with a : calculate the heat released when 1.95 l of cl2g with a density of 1.88 gl reacts with an excess of sodium metal at
Calculate the concentrations of fe3 scn - and fescn2 in a : at a certain temperature k 9.1 10-4 for the following reaction.fescn2aq fe3aq scn -aqcalculate the concentrations of
An air compressor takes air from outdoors at 28deg c and : an air compressor takes air from outdoors at 28deg c and 101.2kpa and compresses it to 790kpa and 50 deg c. the air
If the partial pressure of no is decreasing at the rate of : the following reaction is carried out in a closed vessel.2 nog cl2g ---gt 2 noclgif the partial pressure of no is
The coeficient of discharge is 097 calculate the rate of : a ventuti meter installed in a horizantal water main of diameter 150mm has athroat diameter of75mm. the coeficient of
How is the solubility of manganeseii sulfide affected by : consider the dissolution of mns in water ksp 3.0 times 10-14.mnss h2ol picture mn2aq hs-aq oh-aqhow is the
A four pole 60hz 50 hp synchronous motor has an applied : a four pole 60hz 50 hp synchronous motor has an applied line voltage of 480 volts and draws 60a from the line. it is
Oxygen is flowing through a nominal 2 inch schedule 40 : oxygen is flowing through a nominal 2 inch schedule 40 steel pipe pipe at a velocity of 10 fts. the oxygen is at a
While doing experiment on loadtest on dcshunt : while doing experiment on loadtest on dcshunt generatorwhat happens when dc shunt generator is replaced by dc

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the eccentricity

A satellite is in Earth with an altitude at perigee of 550 km and an altitude at apogee of 5000 km.

  At what location s will the combined moment

At what location s will the combined moment of the weights of the man and platform about point B be zero.

  What is the primary difference between the strength

What is the primary difference between the strength of a structure and the strength of a material? Is a strong material stiff?

  Explain compressive stress

Important information about Compressive Stress, A circular cross sectional bar with a diameter of 3.25 inches is loaded with a uniform axial compressive load of 22,750 pounds. What is the compressive stress along a cross section of the bar?

  A cylindrical drill with radius r1 is used to bore

a cylindrical drill with radius r1 is used to bore vertically a hole through the centre of a sphere of radius r2.a find

  Create a window in java

Create a window apllication in java

  Design value for the molded friction material and steel disk

Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?

  Determine the percent increase in the velocity of air

If the density of air is 1.20 kg/m^3 at the inlet and 1.05 kg/m^3 at the exit, determine the percent increase in the velocity of air as it flows through the dryer.

  A variable force and appropriate energy transfers are

ten kilograms of water initially at 3000 kpa 200degc are contained in a piston-cylindernbspdevice shown below. a

  Determine the rate of heat loss from the molten salt

Determine the rate of heat loss from the molten salt per meter length of the pipe.

  Determine an expression for the number of cycles to failure

Determine an expression for the number of cycles to failure, Nf if the initial crack size is a0. State any assumptions you make.

  Determine the maximum velocity reached

A 0.7-lb block rests on top of a 0.5-lb block supported by but not attached to a spring of constant 9 lb/ft. The upper block is suddenly removed. Determine (a) the Maximum velocity reached by the 0.5-lb block, (b) the maximum height reached by the..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd