The cannons bore is 15 m long find delta t the time that

Assignment Help Mechanical Engineering
Reference no: EM13632167

A cannonball is shot from a boat that's initially moving at 3 m/s in the i direction and subsequently strikes the dock at 300 m/s. The cannonball's mass is 5 kg and the boat's mass is 300 kg. Assume that for all the time that the cannonball was being projected through the cannon's bore it was acted on by a constant force (due to the expanding gases) and that when it exited the cannon the force immediately went to zero. The cannon's bore is 1.5 m long. Find delta t, the time that the cannonball takes to travel through the cannon, as well as the final velocity of the boat.

Reference no: EM13632167

Questions Cloud

A slender rod is at rest in vertical position with lenght : a slender rod is at rest in vertical position with lenght of 1.5m. then a force of 50 n. is applied at the bottom tip.
A piston-cylinder device initially contains 035-kg steam at : a piston-cylinder device initially contains 0.35-kg steam at 3.0 mpa 240 degrees celcius. the steam loses heat to the
A vehicle is to be propelled by a jet of water inclined 15 : a vehicle is to be propelled by a jet of water inclined 15 degrees impinging on a vane as shown in figure 16.16. the
A new planet which has ten times the mass of the earth and : a new planet which has ten times the mass of the earth and four times the radius.a what is the acceleration due to
The cannons bore is 15 m long find delta t the time that : a cannonball is shot from a boat thats initially moving at 3 ms in the i direction and subsequently strikes the dock at
If the ball is kicked at 45 degrees above the horizontal : in us football after a touchdown the team has the opportunity to earn a point by kicking the ball over a bar between
Construct a scatter plot find the value of the linear : listed below are the overhead widths in cm of seals measured from photographs and the weights in kg of the
At the a05 level of significance test for any differences : a study reported in the journal of small business management concluded that self employed individuals do not experience
Sketch the root locus for teh characteristic equations of : sketch the root locus for teh characteristic equations of the system for whichls s2 ss1s5and determine the value of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd