User Account

All Pages

The bumper consists of an 800 kg mass that the car runs

Assignment Help Mechanical Engineering
Reference no: EM13612965

A freight car of mass 1800 kg is timed at 4.2m/s just after it runs into a spring-loaded bumper at the end of the track. The bumper consists of an 800 kg mass that the car runs into, and a pair of large springs. The car travels 2.4m before coming to rest.

a) using an appropriate conservation of law, find the speed of the freight car before it struck the bumper.
b) find the time taken for the car to be brought to rest.

Reference no: EM13612965

Questions Cloud

Two lenses with focal lengths f15cm and f210cm are located : two lenses with focal lengths f15cm and f210cm are located 5cm apart. if an object 2.50 high is located 15.0 cm in
A 50kg box is pulled horizontally with a 45-n force that : a 5.0kg box is pulled horizontally with a 45-n force that makes angle of 40 degrees with the horizontal. the
Kasten company manufactures bowling balls through two : kasten company manufactures bowling balls through two processes molding and packaging. in the molding department the
Use this information to develop linenar equation in : according to the census there were 61 people per square mile. this is called the population density in a certian
The bumper consists of an 800 kg mass that the car runs : a freight car of mass 1800 kg is timed at 4.2ms just after it runs into a spring-loaded bumper at the end of the track.
A decorative light fixture in an elevator consists of a 20 : a decorative light fixture in an elevator consists of a 2.0 kg light suspended by a cable from the ceiling of the
The specifications on an electronic component in a target : the specifications on an electronic component in a target acquisition system are that its life must be between 5000 -
The controller of dugan industries has collected the : the controller of dugan industries has collected the following monthly expense data for use in analyzing the cost
Two different manufacturing processes can be used both of : the specifications on an electronic component in a target acquisition system are that its life must be between 5000 -

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Sketch the schematic diagram of the circuit with the two

two resistors are given r1 470 ohms and r2 1200 ohms a the two resistors are connected in series with a 48 v source.

  Determine the angular speed magnitude of the angular

a 3.6 kg rocket body containing 1.59 kg of fuel is attached to a light rigid rod of length r 0.45 m. the rod pivots

  Consider a container of volume 250ml that is divided into

consider a container of volume 250ml that is divided into two compartments of equalnbspsize. in the left compartment

  Velocity and radius of curvature

Strategy formulation presupposes a set of objectives and goals.

  An instrument having a resonance frequency of 1414 rads

an instrument having a resonance frequency of 1414 rads with a damping ratio of 0.5 is used to measure a signal of 6000

  Compare the pressure force exerted on the face of two dams

Fluid/Dam Pressure, Compare the pressure force exerted on the face of two dams that hold a fresh water of 1000 Kg/m^3 density and a salty water of 1030 Kg/m^3

  A square 3m x 3m gate is located in the 45 sloping side of

a square 3m x 3m gate is located in the 45 sloping side of a dam. some measurements indicate that the resultant force

  The water exits the chamber as a saturated liquid at the

liquid water at 50degc and 1 mpa is mixed with superheated steam at 200degc and 1 mpa in an open feedwater heater

  What is the mechanical advantage of the system

A block and tackle system with nine supporting strands is used to lift a metal lathe in a manufacturing plant. The motor being used to wind the cable in the pulley system can provide 100 lb. of force.

  Determine a the volume and mass flow rates of water through

a garden hose attached with a nozzle is used to fill a 10-gallon bucket. the inner diameter of the hose is 2 cm and it

  Its specific heat ratio is 14 and gas constant is 0287

an open brayton cycle engine operates with a compressor-pressure ratio of 6 an inlet temperature of 20 c and inlet

  Wind turbines are becoming more and more common as a method

wind turbines are becoming more and more common as a method of energy production wind turbines by their very nature are

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd