The block diagram for an elevator controller for a

Assignment Help Electrical Engineering

Reference no: EM13345859

The block diagram for an elevator controller for a two-floor elevator follows. The inputs FB1 and FB2 are 1 when someone in the elevator presses the first or second floor buttons, respectively. The inputs CALL1 and CALL2 are 1 when someone on the first or second floor presses the elevator call button. The inputs FS1 and FS2 are 1 when the elevator is at the first or second floor landing. The output UP turns on the motor to raise the elevator car. The output DOWN turns on the motor to lower the elevator. If neither UP nor DOWN is 1, then the elevator will not move. R1 and R2 reset the latches (described below); and when DO goes to 1, the elevator door opens. After the door opens and remains open for a reasonable length of time (as determined by the door controller mechanism), the door controller mechanism closes the door and sets DC = 1. Assume that all input signals are properly synchronized with the system clock.

Please apply the following guidelines to your design.
If you were to realize an elevator controller that responded to all of the inputs FB1, FB2, CALL1, CALL2, FS1, FS2, and DC, you would need to implement logic equations with nine or more variables (seven inputs plus at least two state variables). However, if you combine the signals FBi and CALLi into a signal Ni (i = 1 or 2) that indicates that the elevator is needed on the specified floor, you can reduce the number of inputs into the control circuit. In addition, if the signal Ni is stored so that a single pulse on FBi or CALLi will set Ni to 1 until the control circuit clears it, then the control circuit will be simplified further. Using a D flipflop and a minimum number of added gates, design a storage circuit that will have an output 1 when either input (FBi or CALLi) becomes 1 and will stay 1 until reset with a signal Ri.
Using the signals N1 and N2 that indicate that the elevator is needed on the first or second floor (to deliver or pick up passengers or both), derive a state graph for the elevator controller. (Only four states are needed.)
Realize the storage circuits for N1 and N2 as describe in the design specification.

Reference no: EM13345859

Questions Cloud

At a given instant in time flywheel oa is caused to rotate : at a given instant in time flywheel oa is caused to rotate with angular velocity of w2radsec and angular acceleration o

Consider a sinusoidal wave with frequency of 300khz as a : consider a sinusoidal wave with frequency of 300khz as a carrier signal. we want to transmit a sinusoidal signal with

Calculate the enthalpy entropy and gibbs free energy : a.calculate the enthalpy entropy and gibbs free energy changes when 10g of supercooled liquid silver solidifies

If 100 ml of 005m nacl is added to 2000 ml of solution : solid nacl is added slowly to a solution containing 0.10 m agno3 and 0.20 m pbno32. ksp for agcl is 1.8x10-10. ksp for

The block diagram for an elevator controller for a : the block diagram for an elevator controller for a two-floor elevator follows. the inputs fb1 and fb2 are 1 when

In a reaction where pbcl2 precipitate was formed using : in a reaction where pbcl2 precipitate was formed using pbno33 and hcl explain why the pbcl2 precipitate dissolved when

At 250degc a sample of xe gas occupies 550 ml in a : at 25.0degc a sample of xe gas occupies 550 ml in a piston-cylider apparatus when the external pressure is 353 torr. at

An insulated piston-cylinder device contains 2l of : an insulated piston-cylinder device contains 2l of saturated liquid water at a pressure of 150kpa-which is constant

Discuss the pros and cons of the various methods of : discuss the pros and cons of the various methods of application of solid fertilizers. describe the revelant facets of

User Account

All Pages