The average heat transfer coefficient is 20 btuhr ft2 f the

Assignment Help Mechanical Engineering
Reference no: EM13621899

Air enters a 1 ft diameter 36 ft long duct at 140f and 1 atm at a mean velocity of 21 ft/sec. The stream is cooled by the water outside the duct. The average heat transfer coefficient is 20 Btu/hr ft^2 F. The duct temperature is constant at 50 F. Determine the exit air temperature and the rate of heat transfer.

Reference no: EM13621899

Questions Cloud

Currently neither ken nor sandra has disability insurance : 1. if a shed valued at 13000 in the backyard is also destroyed in the fire what is the maximum amount that the
Assuming no inflation and an interest rate of 4 what : a a truck is purchased for 20000. at the end of its 5 year life its salvage value will be 2000. using general straight
The cross section for neutron absorption on 197au is 988 : a 43 mg sample of pure gold 197au is irradiated in a reactor with a steady neutron flux of 51010 neutronss-cm2 long
Calculate the binding energy of 23 na using the table of : a calculate the binding energy of 23na using the table of atomic masses. express your answer in unified mass units but
The average heat transfer coefficient is 20 btuhr ft2 f the : air enters a 1 ft diameter 36 ft long duct at 140f and 1 atm at a mean velocity of 21 ftsec. the stream is cooled by
Calculate the specific cost of each source of financing if : 1bryant labs has asked its financial manager to measure the cost of each specific type of capital as well as the
According to the irs the average tax refund for the 70 : according to the irs the average tax refund for the 70 million personal income tax returns in 1998 was 800. assuming a
What is the magnitude of the average emf produced what will : a wire coil of 30 turns has a cross-sectional area of 10 cm2. the coil is placed in a uniform field of a large magnet
For 2012 everyday electronics reported 225 million of sales : for 2012 everyday electronics reported 22.5 million of sales and 19 million of operating costs including depreciation.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd