The african elephant has developed the pinna or external

Assignment Help Mechanical Engineering
Reference no: EM13624535

The african elephant has developed the pinna or external ear that functions as a radiator-convector. The pinna can be modeled as a flat plat with air flow over it. If the rate of metabolic heat production for a 2000 kg elephant is 1650 W, what is the maximum percentage of the metabolic heat that can be lost by convection through the pinna? Remember that an elephant has two ears, and heat is lost equally from both sides of the ear. The ambient air temperature is 20 C, the air velocity is 2 m/s, the surface area of one ear is 0.84 m^2, and the average length of one side of the ear is 1 m. I'm also give density is of air at 20 C (~290 in K) is 1.2177 km/m^3, specific heat is 1.0057 kJ/Kg*K, viscosity is 2.7504X10^5, thermal conductivity is 0.02547 W/m*K, thermal diffusivity is 2.0792x10^5 m^2/s and the Prandtl number is 0.710.

Reference no: EM13624535

Questions Cloud

Researchers investigated the issue of race and equality of : researchers investigated the issue of race and equality of access to clinical trials. the table below shows the
The setup is such that pressure is proportional to volume p : a spring-loaded pistoncylinder assembly contains water at 500 c and 3 mpa. the setup is such that pressure is
A 12 cantilever beam has a 4000 lb load at the end of the : a 12 cantilever beam has a 4000 lb load at the end of the beam. draw the shear force and bending moment diagrams and
A steel rod with a diameter of 0625 is loaded in tension : a steel rod with a diameter of 0.625 is loaded in tension with 12000 lb load. in the unloaded condition the rod is 240
The african elephant has developed the pinna or external : the african elephant has developed the pinna or external ear that functions as a radiator-convector. the pinna can be
Saturated water vapor in a closed sysytem is condensed by : saturated water vapor in a closed sysytem is condensed by cooling it at constant pressure to a saturated liquid at
A binomial probability experiment is conducted with the : a binomial probability experiment is conducted with the given parameters. compute the probability of x successes in the
The water is then cooled until the piston is on the lower : water is contained in a vertical cylinder fitted with a frictionless piston and two sets of stops. the volume is 0.1m3
If you want to be 95 confident of estimating the : if you want to be 95 confident of estimating the population proportion to within a sampling error of plus or minus 0.05

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd