The actual combustion is to take place with 15 excess air

Assignment Help Mechanical Engineering
Reference no: EM13629753

A gas stream produced as a by-product of a petroleum processing operation is to be used as a fuel in a small electric generation facility. The gas composition, in volume %, is:
CH4 (methane) 82%, C2H6 (ethane) 18%
The gas flow rate is 200 standard liters per minute (0oC definition).

1. Determine the air feed rate for a stoichiometric feed ratio.

2. The actual combustion is to take place with 15% excess air. Determine the composition (vol%) and flowrate (std L /min) of the gases leaving the burner if 95% of the fuel is completely consumed and the product gas contains no CO (all carbon in the fuel which reacts forms CO2). Apply the 95% to each component of the fuel.

3. If the electrical generation process is 30% efficient, determine the maximum electrical current and power that can be generated at a voltage of 240 volts. Fuel Energy Values: Methane: 900 kJ/mol, Ethane: 1560 kJ/mol

Reference no: EM13629753

Questions Cloud

What is the direction of the force that you exert on the : a what is the direction of the force that you exert on the coin during the toss but before the coin leaves your hand?b
Super cola sales breakdown is 80 regular soda and 20 diet : super cola sales breakdown is 80 regular soda and 20 diet soda. of the regular soda 60 are purchased by men. of the
Nine coins are tossed let x be the number of coins that : a nine coins are tossed. let x be the number of coins that turn up heads. find px 4 and px 6.b a coin is tossed
A spring-mass system is found to vibrate with a frequency : a spring-mass system is found to vibrate with a frequency of 120 cycles per minute in air and 100 cycles per minute in
The actual combustion is to take place with 15 excess air : a gas stream produced as a by-product of a petroleum processing operation is to be used as a fuel in a small electric
What is the shape of isopycanal surface between 400 and : surface geostrophic velocity 0.5 ms density 1026kgm3 gravity 9.8ms ring radius 50km. you take velocity measurment
Steam is leaving a pressure cooker whose operating pressure : steam is leaving a pressure cooker whose operating pressure is 30 psia. the amount of liquid inside the pressure cooker
Suppose the lifetime of a particular appliance follows an : suppose the lifetime of a particular appliance follows an exponential distribution with a mean of 10 years. what is the
Suppose a liquid level ranging from 55 to 86 m is linearly : question 1. which of the following would be used for the highest temperature measurements ?thermistorthermocoupleic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd