The 4-mm-diameter cable bc is made of a steel with e 200

Assignment Help Mechanical Engineering
Reference no: EM13624047

The 4-mm-diameter cable BC is made of a steel with E = 200 Gpa. Knowing that the maximum stress in the cable must not exceed 190 Mpa and that the elongation of the cable must not exceed 6 mm, find the maximum load P that can be applied as shown.

Reference no: EM13624047

Questions Cloud

The accerleration of a particle is defined by the relation : the accerleration of a particle is defined by the relation a a - 6t2 where a is constant. at t 0 the particle starts
When the coil is turned slightly and released it oscillates : a circular coil of 16 turns and radius 10 cm carrying a current of 0.75 a rests with its plane normal to an external
A use the sample data to construct a 95 confidence interval : a study of 420039 cell phone users found that 131 of them developed cancer of the brain or nervous system. prior to
Consider a solid rod with diameter d and length l subjected : consider a solid rod with diameter d and length l subjected to torsion t and moment m at both ends shown in fig. 1.
The 4-mm-diameter cable bc is made of a steel with e 200 : the 4-mm-diameter cable bc is made of a steel with e 200 gpa. knowing that the maximum stress in the cable must not
When the coil is turned slightly and released it oscillates : a circular coil of 16 turns and radius 10 cm carrying a current of 0.75 a rests with its plane normal to an external
R-410a flows inside the tubes and evaporates at a constant : the cooling coil of a small air-conditioning system is to be designed for a heat-transfer rate of 48000 btuhr from air
The following is a cross-tabulation taken from a subset of : the following is a cross-tabulation taken from a subset of the 2010 general social survey. respondents were asked
What is the force and torque on the solenoid if a uniform : a closely wound solenoid of 2000 turns and area of cross-section 1.6 times 10-4 m2 carrying a current of 4.0 a is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Estimate the schmid factor

Estimate the Schmid Factor, which is used to convert the CRSS into a critical tensile 'yield' stress. Use the measured angle between the slip trace and the sample long axis

  At what true event rate will dead time losses not to be

counters a and b are non-paralyzable with dead times of 30 or 100 microseconds respectively. at what true event rate

  Two kilograms of air within a piston-cylinder assembly

two kilograms of air within a piston-cylinder assembly executes a carnot power cycle with maximum and minimum

  Iin the other stream refrigerant 134a enters at 10 bar 80

a wellinsulated counterflow heat exehanger operates at steady state. in one stream liquid water enters at 10 degree

  Optimus prime is flying straight up at 67 ms when he

optimus prime is flying straight up at 67 ms when he accidentally drops his mega-ray blaster and it falls 76 m to the

  Compare annual profit when the plant is operating at 90 of

a planet operation has fixed costs of 2000000 per year and its output capacity is 100000 electrical appliances per

  Determine the maximum lift force provided by the pump

the velocity of a lift increases uniformly from zero to its maximum value at mid-height (1.4m) in 7.5s and then decreases uniformly to zero in 7.5s. The peak power output is 6kW when the velocity is maximum, determine the maximum lift force provid..

  The static pressure as 55 kpa and stagnation temperature as

a thermocouple place in the mouth of a pitot tube can be used to measure the stagnation temperature of the flow. such

  The distance from the end of the bar touching the ground

there is a bar leaning on a perfect half cylinder with radius r. the end of the bar touching the ground is pulled with

  An open feed water heater incorperated with the steam cycle

consider a combined gass steam power plant that has a net power output of 450 mw. the pressue ratio of the gas turbine

  What is the rate of flow of cooling water through the

consider an ideal steam cycle that combines the reheat cycle and the generative cycle. the net power output of the

  Determine the maximum stress and the maximum shearing stress

Knowing that the gage pressure inside the tank is 5 MPa, determine the maximum stress and the maximum shearing stress at point L.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd