Tetrafluoroethylene-vinyl chloride is other repeat unit

Assignment Help Mechanical Engineering
Reference no: EM13705503

An alternating copolymer is known to have a number-average molecular weight of 100000 g/mol and a degree of polymerization of 2210. If one of the repeat units is ethylene, which of styrene, propylene, tetrafluoroethylene, and vinyl chloride is the other repeat unit?

A: vinyl chloride

B: propylene

C: tetrafluoroethylene

D: styrene

Reference no: EM13705503

Questions Cloud

Determine the velocity of the ball relative to the fielder : A batter hits the baseball A with an initial velocity of v0 = 103 ft/sec directly toward fielder B at an angle of 34° to the horizontal; the initial position of the ball is 2.0 ft above ground level. Fielder B requires 0.43 sec to judge where the bal..
Find the force that the third person is exerting : Three people are pulling on a box. The first person is pulling with a force of 100 N at 37 degrees with respect to the positive x-axis. find the force that the third person is exerting
What is the change in internal energ : Question- 1.50 mol of helium gas in a cylinder is held at a volume of 22.4 L by a piston at 273K and 1.00 atm. Heat is supplied to the system to double the volume and temperature of the gas while maintaining the internal pressure at 1.00 atm.
Estimate what total retarding force must be supplied : The parachute on a race car of weight 8940 N opens at the end of a quarter mile run when the car is traveling at 38.0 m/s. What total retarding force must be supplied
Tetrafluoroethylene-vinyl chloride is other repeat unit : An alternating copolymer is known to have a number-average molecular weight of 100000 g/mol and a degree of polymerization of 2210. If one of the repeat units is ethylene, which of styrene, propylene, tetrafluoroethylene, and vinyl chloride is the ot..
Explain what is the molality of the sugar solution : Question- A 2.00 g sugar cube (sucrose- C12H22O11) is dissolved in a 350 mL teapot containing 80 C water (density of water at 80 C= 0.975 g/mL). What is the molality of the sugar solution
At what time does the particle reach its positive position : The position of a particle moving along the x-axis depends on time as x(t) = 30 t2 - 4 t3 where x is in m and t in s. At what time does the particle reach its maximum positive x position
Suggestion of atm-like machines to improve delivery options : Write a well presented report for the above outlining the business operation. Do not use any trademarked restaurant name in your report -  Provide suggestions into improving business service
What is the ?grxn of the reaction : Question- What is the ?Grxn of the reaction below at 25C when [NO2-]=[H3O+]=1x10^-5 M and [HNO2] = 1M? Will the reaction be spontaneous or non-spontaneous?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd