User Account

All Pages

Temperature of the air and the surroundings

Assignment Help Mechanical Engineering
Reference no: EM13880742

Steam at a temperature of 250°C flows through a steel pipe (AISI 1010) of 60-mm inside diameter and 75-mm outside diameter. The convection coefficient between the steam and the inner surface of the pipe is 500 W/m2 · K, while that between the outer surface of the pipe and the surroundings is 25 W/m2 · K. The pipe emissivity is 0.8, and the temperature of the air and the surroundings is 20°C. What is the heat loss per unit length of pipe?

Reference no: EM13880742

Questions Cloud

Draw scatterplot with country group of each point indicated : Choose two of the three original variables. Draw a scatterplot with the country group of each point indicated. Comment. Generate classification rules using Linear discriminant analysis.
Determine the primary manner in which orion has increased : Determine the primary manner in which ORION has increased your business knowledge in the related subject area
What explanation might there be for such a strategy : Before the merger, each of the separate newspapers was losing about $10 million per year. What forecast would you make for the merged firms' profits? Explain.
Annual coupon payments : A bond with a face value of $1,000 has annual coupon payments of $100 and was issued 7 years ago. The bond currently sells for $1,000 and has 8 years remaining to maturity. This bond’s must be 10%.
Temperature of the air and the surroundings : The pipe emissivity is 0.8, and the temperature of the air and the surroundings is 20°C. What is the heat loss per unit length of pipe?
Find the firm''s optimal output : Create a spreadsheet to describe the firm's profit as it varies with output and advertising. Set advertising spending at 50 and find the firm's optimal level of output.
Describe and compare the managerial behavior of ben and phil : Describe and compare the managerial behavior of Ben and Phil. To what extent does each manager display specific relations behaviors (supporting, developing, recognizing) and specific task behaviors (clarifying, planning, monitoring)? To what exten..
Develop a plan for how to resolve ethical and legal issues : Develop a plan for how to resolve ethical and legal issues
Analysis of starbucks corporation : Review the requirements of the Chapter 3 Mini-Case, parts b through h. Then apply those requirements to do an analysis of STARBUCKS CORPORATION (TICKER: SBUX). Don't complete the mini case itself, just STARBUCKS. Do the analysis on the basis of the f..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider installation on the bottom of the attic roof only

consider the attic of a home located in a hot climate. the floor of the attic is characterized by a width of l1 10 m

  An orthopedic called mend-a-bone is made of an

1. an orthopedic called mend-a-bone is made of an extracellular matrix extract plasticized with glycerol mw92 to help

  The coefficent between a and c and horizontal surface is

assuming mass of block a 5kg mass of block b 10 kg mass of block c10kg. the coefficent between a and c and

  If the compressor consumes 450 w of power determine a the

a refrigerator uses 134a as the working fluid and operates on the ideal vapor-compression refrigeration cycle. the

  Determined the rate of energy transfers by mass into and

refrigerant 134a enters the compressor of a refrigeration system as saturated vapor at 0.14mpa and leaves at

  1 kg of propane is contained in a piston - cylinder

1 kg of propane is contained in a piston - cylinder assembly at a constant pressure of .20 mpa heat transfer slowly to

  Suitable face width based on an allowable bending stress

A steel spur gear has a module of 1 mm and 16 teeth cut on the 20° full-depth system and is to carry 0.15 kW at 400 rev/min. Determine a suitable face width based on an allowable bending stress of 150 MPa. Use the first approximation equation for ben..

  Sketch the ewald sphere construction for the 200

sketch the ewald sphere construction for the 200 diffraction with mo kalpha radiation and a poly crystalline specimen

  The enthalpies of the gas at entry asnd exit are 950 kjkg

a stream of gases at 7.5 bar 750 ordmc and 140 ms enters the turbine of a jet engine. the stream comes out of the

  The volume of 1 kg of helium in a piston-cylinder device is

the volume of 1 kg of helium in a piston-cylinder device is initially 5m3. now the helium is compressed to 3m3 while

  A material is found to have a tenth-thickness of 23 cm for

a material is found to have a tenth-thickness of 2.3 cm for 1.25-mev gamma rays. a what is the linear attenuation

  What factors limit dislocation mobility

Explain why metals are ductile and ceramics are brittle, in terms of their dislocation motion. Draw 2 pictures to sequentially show an edge dislocation gliding through a crystal, using dots to represent the atoms. Draw 2 pictures to show how a disloc..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd