Taking the properties of the egg to be rho 1020 kgm3 and

Assignment Help Mechanical Engineering
Reference no: EM13639747

An ordinary egg can be approximated as a 5.5-cm-diameter sphere. The egg is initially at a uniform temperature of 8C and is dropped into boiling water at 97C. Taking the properties of the egg to be ρ = 1020 kg/m3 and cp = 3.32 kJ/kgC, determine how much heat is transferred to the egg by the time the average temperature of the egg rises to 80C.

Reference no: EM13639747

Questions Cloud

Compute the value of the exponent in the relationship pv pv : a cylinder filled with 50 gm of air at 1 atmosphere pressure and a temperature of 20 c is adiabatically but
When a 06333-g sample of a compound of carbon hydrogen and : when a 0.6333-g sample of a compound of carbon hydrogen and sulfur was burned in excess oxygen 0.9272 g co2 0.3795 g
Determine the amount of extra heat that must be supplied to : a frictionless piston-cylinder device and a rigid tank initially contain 12kg of an ideal gas each at the same
To maintain the temperature inside a house at 20deg c the : to maintain the temperature inside a house at 20deg c the electric power consumption of the electric baseboard heaters
Taking the properties of the egg to be rho 1020 kgm3 and : an ordinary egg can be approximated as a 5.5-cm-diameter sphere. the egg is initially at a uniform temperature of 8c
A flight attendant pulls her 60 n flight bag a distance of : a flight attendant pulls her 60 n flight bag a distance of 358 m along a level airport floor at a constant velocity.
Determine the reduction in the exit temperature of the : the compression stages in the axial compressor of the industrial gas turbine are closed coupled making intercooling
Liquid nitrogen has a density of 0808gml at 77 k a sample : liquid nitrogen has a density of 0.808gml at 77 k. a sample of 2.5 l of liquid nitrogen is allowed to evaporate at
The test for this drug is 90 accurate for users of the drug : it is estimated that 3 of the athletes competing in a large tournament are users of an illegal drug to enhance

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the minimum required length of the rod so that one

a high strength steel drill rod used for boring a hole in the earth has a diameter of 0.5 in. the allowable shear

  The allowable shear stress in the bolts is 10000 psi

a flanged coupling joins two pieces of 4-in diameter shaft. the .625 bolts are arranged in a single 8 diameter bolt

  The heat flux through a 1-mm thick layer of skin is 105 x

the heat flux through a 1-mm thick layer of skin is 1.05 x 104 wm2. the temperature at the inside surface is 37degc and

  The pump of a water distribution system is powered by a

the pump of a water distribution system is powered by a 6-kw electric motor whose efficiency is 95. the water flow rate

  If the x component of acceleration is ax14t2 ms2 where t

a rocket is fired from rest at x0 and travels along a parabolic trajectory described by y2120103xm. if the x component

  Determine a the final temperature of the steam in the tank

118 an insulated rigid tank whose volume is 0.5 m3 is connected by a valve to a large vessel holding steam at 40 bar

  Find the final temperature if 400 btu of heat is added to

twenty pounds of a gas mixture is contained in a tank with volume 30 cubic feet at 30 psia and 70 f. the gas mixture

  An airplane was moving with a velocity equal to 300mph when

an airplane was moving with a velocity equal to 300mph when the velocity was increased with uniform acceleration to

  A simple steam power system has a turbine inlet state of

a simple steam power system has a turbine inlet state of 120 bars and 600c and exhaust pressure of 0.08 bar. the

  Determine a the exit velocity of the nitrogen and b the

nitrogen gas at 60 kpa and 7degc enters an adiabatic diffuser steadily with a velocity of 275 mls and leaves at 85 kpa

  Find the maximum temperature in wall

The heat transfer convection coefficient between the wall and the fluid is 500 W/m2.K. Find the maximum temperature in wall.

  Determine the analytical solution for the maximum stress

Determine the analytical solution for the maximum stress of the beam shown; compare with stress results from SolidWorks.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd