Steam flows through a small steam turbine

Assignment Help Mechanical Engineering
Reference no: EM13717669

Steam flows through a small steam turbine at the rate of 10,000 kg/hr, entering at 600 C and 2 MPa and emerging at 0.01 MPa with 4% moisture. The flow enters at 50 m/s at a point 2 m above the discharge and leaves at 80 m/s. Compute the shaft-power output [MW], assuming that the device is adiabatic but considering kinetic and potential energies. How much error would be made were these secondary terms were neglected? Show the process on a P-v state diagram.

Reference no: EM13717669

Questions Cloud

The population proportion of americans with diabetes : The population proportion of Americans with diabetes is 9 percent (uc0u960 = 0.09). In repeated random samples of n = 800 Americans, 90% of sample proportions of people with diabetes would fall within______ from
Carbon dioxide gas undergoes process in closed system : Carbon dioxide (CO2) gas undergoes a process in a closed system from T1=100 F, p1=20 lbf/in^2 to T2=400 R,p2=50 lbf/in^2. The entropy produced due to internal irreversibilities during the process is determined to be 0.15 Btu/R per lb of gas.
Test the claim that with garlic treatment : Test the claim that with garlic treatment, the mean change in LDL cholesterol is greater than 0. What do the results suggest about the effectiveness of the garlic treatment?
What are the chemical composition-mechanical properties : What are the chemical composition, mechanical properties, and typical uses of Aluminium 6061, 360 brasses, 1045 steel, and 4140 steel? What do the numbers in 6061, 1045, 360, and 4140 represent? Comment on the transition temperature of the materials,..
Steam flows through a small steam turbine : Steam flows through a small steam turbine at the rate of 10,000 kg/hr, entering at 600 C and 2 MPa and emerging at 0.01 MPa with 4% moisture. The flow enters at 50 m/s at a point 2 m above the discharge and leaves at 80 m/s. Compute the shaft-power o..
The number of hours a student watches tv : Select two variables that might be related, such as the number of hours a student watches TV and the number of credits the student has, or a baseball player's salary and the number of home runs per year the player scores. You will need to get..
Determine the outlet density of the steam : Saturated liquid steam at 2 MPa steadily enters a valve where it is throttled to 0.3 MPa. The inlet and outlet diameter is 1 cm. The flow rate is 0.012 kg/s. Determine the outlet density [kg/m3] of the steam. Also show that it is reasonable to neglec..
Calculate the percent yield of the reaction : Calculate the percent yield of the reaction if 25.0 g of calcium hypochlorite were produced from the reaction of 40.8 g of molecular chlorine and 33.9 g of calcium hydroxide.
Explain what is the atomic mass of the unknown element x : There are three isotopes, Xa has a mass of 54.68 g and is 2.36% abundant, Xb has a mass of 53.89 g and is 45.69% abundant, and Xc has a mass of 61.42 g and is 51.95% abundant. What is the atomic mass of the unknown element X

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd