Steam at 300 degc travels through a pipe covered with two

Assignment Help Mechanical Engineering
Reference no: EM13623642

Steam at 300 °C travels through a pipe covered with two layers of insulation. The first layer of insulation is 3 cm thick and the second layer is 5 cm thick. The pipe is made of steel (k = 58 W/m-K) and has an IDof 160 mm and an OD of 170 mm. Air at 50 °C flows over the pipe. The convection coefficients of the inside and outside flows are 30 and 5.8 W/m2 -K, respectively.

a. Draw an electrical schematic that is equivalent to the thermal network.

b. Identify assumptions applicable to this problem.

c. What is the equivalent or total thermal resistance?

d. Calculate the heat transfer

Reference no: EM13623642

Questions Cloud

A company is develoing a new golf ball the overall distance : a company is develoing a new golf ball. the overall distance is approximately normally distributed and has a standard
What are the adavanteges and disadvantages of project : 1-what are the adavanteges and disadvantages of project managment?2-what are the key charactristics all project
If the two sides of the plate are maintained at 100 degc : heat is generated uniformly in a steel plate k 20 wm-k 1 cm thick at the rate of 500 mwm3. if the two sides of the
Four balls are randomly placed one at a time into four : four balls are randomly placed one at a time into four urns so that it is possible for more than one ball to be in any
Steam at 300 degc travels through a pipe covered with two : steam at 300 degc travels through a pipe covered with two layers of insulation. the first layer of insulation is 3 cm
The following data represents the time it takes a company : the following data represents the time it takes a company to respond to an account inquiry for opening a new account.a.
The following partial minitab printout of a regression : the following partial minitab printout of a regression analysis where x is the number of calories per serving and y is
In december when the temperature is 4 f -15 c the volume of : an eng must design a large natural gas storage tank to be expandable to maintain the pressure constant at 2.2 atm. in
A thermometer flashes the temperature in celsius and : q1. a thermometer flashes the temperature in celsius and fahrenheit along with the time. if it flashes -4deg f what

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd