Stainless steel pressure vessel is made of long tubing

Assignment Help Mechanical Engineering
Reference no: EM13713487

A stainless steel pressure vessel is made of long tubing having an outside diameter of 1.5 in and a wall thickness of 1/4 in. (1) what maximum internal pressure (zero external pressure) can the cylinder carry if the permissible tangential stress is 60 ksi and the theory for thick walled vessels is assumed to apply? (2) What maximum external pressure (zero internal pressure) can the cylinder carry assume the same permissible tangential stress limit applies?

Reference no: EM13713487

Questions Cloud

Aluminium rod corresponding to the design safety factor : A solid round aluminium rod (made of 6061-T6) has a mean yield strength Sy = 40.0 ksi with standard deviation of 4.0 ksi, the rod is to be subjected to a mean static axial load of P = 25 kip with a standard deviation of 2.5 kip.
Dimensional analysis to find expression for pump efficiency : The efficiency of a pump is assumed to be a function of the flow rate Q (cubic ft/sec), pressure increase? p, pipe diameter d, and density and viscosity of the fluid. Use dimensional analysis to find an expression for the pump efficiency.
Ratio of mean strength to mean stress : A solid round aluminium rod (made of 6061-T6) has a mean yield strength Sy = 40.0 ksi with standard deviation of 4.0 ksi, the rod is to be subjected to a mean static axial load of P = 25 kip with a standard deviation of 2.5 kip. Assume the yield stre..
Calculate the temperature of the gas to burn first : An adiabatic constant-volume combustion chamber is filled with a mixture of air and methane; lambda (AFR/AFRs) = 1.3. The initial temperature of the mixture is25°C, and its pressure is 1 bar. After laminar combustion from a single ignition source (an..
Stainless steel pressure vessel is made of long tubing : A stainless steel pressure vessel is made of long tubing having an outside diameter of 1.5 in and a wall thickness of 1/4 in. (1) what maximum internal pressure (zero external pressure) can the cylinder carry if the permissible tangential stress is 6..
What would be the raindrops speed just before landing : A spherical raindrop of mass 0.0162 g and radius 1.57 mm falls from a cloud that is at a height of 1173 m above the ground. What would be the raindrops speed just before landing on the ground if there were no drag force (no air resistance)
Power cycle operates between hot and cold reservoirs : A power cycle operates between hot and cold reservoirs and 310 K, respectively. At steady state the cycle develops a power output of 0.1 MW. Determine the minimum theoretical rate at which energy is rejected by heat transfer to the cold reservoir, in..
Calculate her speed with respect to the shore : Mary needs to row her boat across a 180m -wide river that is flowing to the east at a speed of 1.3m/s . Mary can row with a speed of 2.6m/s. What is her speed with respect to the shore
Compressed adiabatically in a cylinder : A mixture is composed of 2 mol of CO2 and 4 mol of N2 is compressed adiabatically in a cylinder, from 100 kPa and 20C to 2MPa.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd