Specify the horsepower required for the driving motor

Assignment Help Electrical Engineering
Reference no: EM13248656

The primary air fans in the Navaho power plant move 305,000 ft3/min at 100oF and produce a pressure rise if 35 inches of water. Calculate the horsepower required if the isentropic efficiency is 0.8.

Air is to be compressed from atmospheric pressure at 60oF to 100 psia in a centrfugal compressor (isentropic efficiency about 0.7). The flow rate will be 500 lbm/min. Specify the horsepower required for the driving motor

Reference no: EM13248656

Questions Cloud

Determine the net resistance : A 75-W, 120-V bulb is connected in parallel with a35-W, 120-V bulb. What is the net resistance
Compute the voltage across the primary windings : The equivalent inductance of the primary and the secondary circuits is .02H. The frequency of the primary windings is 10Hz. Assume that the drag force is 500N and the friction force is 2kN. Compute the voltage across the primary windings when the ..
What is going to be your competitive advantage : What problems might occur if you do not effectively and efficiently carry out these management functions?
Determine how high up the opposite wall the ball hits : A soccer player kicks a ball toward a wall 15.0 m away, with velocity 25.0 m/s at 30.0 above the horizontal. Determine how high up the opposite wall the ball hits, and nd the impact velocity
Specify the horsepower required for the driving motor : Air is to be compressed from atmospheric pressure at 60oF to 100 psia in a centrfugal compressor (isentropic efficiency about 0.7). The flow rate will be 500 lbm/min. Specify the horsepower required for the driving motor
What controls would be necessary to ensure only valid data : What steps (place them in order from most important to least important) should be taken to develop an effective continuous feedback loop?
What are the positive and negative aspects of medicare : what are the positive and negative aspects of medicare and medicaid services.
What substantial government interest is congress attempting : What substantial government interest is Congress attempting to protect with the National DNC List? Where is that found in U.S. Constitution? What other strategies could the government employ to reach the same result?
Calculate the developed torque at full load : A 480V, 60 Hz three phase induction motor has the following parameters: R1=R' 2= .3 ohms Xeq= 1 ohm Xc=600 ohms At full load, the motor speed is 1120 rpm, the rotational loss is 400W and the core loss is 1 kW.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the modulation index and percentage modulation

When unmodulated the carrier voltage is 75 volts peak. An information (modulating) signal of 15 KHZ with 5 volts peak amplitude causes a frequency deviation of 22.5 KHz. If the load resistor RL= 100 Ohms, determine the following Modulation index

  Find out the laplace transform of the above signals

Determine the Laplace transform of the above signals (use properties of the Laplace transform) including the corresponding region of convergence.

  How to close the temperature switch turns on

In a motor control system, one master stop pushbutton (Stop) is available for stopping the operation at any time. If the temperature switch (TSW) is closed, pressing the red pushbutton (RedPB) will turn on both motors M1 and M2.

  Find the damping ratio and undamped natural frequency

How to find the damping ratio and undamped natural frequency given a 2nd-order differential equation.

  Draw a block diagram with all the necessary input and output

Design an elevator controller for a simple two-floor elevator. On the 1st floor, there is only an up button, and on the 2nd floor, there is only a down button. Within the elevator, there are two buttons: door open and door close.

  How to write a subroutine in assembler for the hcs12

In and Th are inputs and Out is the result. All parameters are 8-bit unsigned integers. A typical calling shows that the two inputs, In and Th, are passed on the stack and the return parameter Out, is returned in RegB.

  Compare a lumped element model of a lossless transmission

Compare a lumped element model of a lossless transmission line (single L and C) with the distributed model. Use the following values for the transmission line in this comparative analysis.

  Find the position as a function of time of the mass

A mass "m = 2 kg" is connected to a spring with spring constant "k= 5 N/m " on a frictionless table oscillation only in 1-D (x direction) . The equation of motion for the mass is given by the equation m (d^2 x(t)/ dt^2) = -kx(t) .

  Calculate the per unit resistance of this transformer

Efficiency in a power transformer is 98.6 percent when loaded such that its copper losses are five times its core losses. Calculate the per unit resistance of this transformer.

  State whether power factor is lagging or leading

The generator is delivering 48 MW to the bus bar at the rated voltage with its field current adjusted for a generated emf of 46 kV per phase. Determine the armature current and the power factor. State whether power factor is lagging or leading

  What is the overall gain if amplification factors given

an amplifier has three amplification stages and a 1-dB attenuator in cascade. Assuming that all the impedances are properly matched, what is the overall gain if the amplification factors are 5, 10, and 6 dB

  What fraction of the widths of the strip should be added

A 78oham lossless planar line was designed but did not meet a requirement. What fraction of the widths of the strip should be added or removed to get the characteristic impedance of 75oham

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd